Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:transistor-tester-adapter:getting-started [2021/05/14 23:07] – ↷ Links adapted because of a move operation Arthur Browntest-and-measurement:transistor-tester-adapter:getting-started [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 15: Line 15:
  
   * Your new //Transistor Tester Adapter//   * Your new //Transistor Tester Adapter//
-  * A computer, with the WaveForms application (version 3.15.22 or later) installed.+  * A computer, with the WaveForms application (version 3.16.3 or later) installed.
     * Installation instructions can be found in the [[software:waveforms:waveforms-3:getting-started-guide]].     * Installation instructions can be found in the [[software:waveforms:waveforms-3:getting-started-guide]].
  
Line 81: Line 81:
 <WRAP column half> <WRAP column half>
  
-A Transistor Tester is also known as a curve tracer and the Transistor Tester Adapter is used to add curve tracer capability to your set of tools. A Curve Tracer plots the current (I) versus voltage (V) to create an I-V curve for an electronic device.  The Transistor Tester allows you to create I-V curves for a bipolar junction transistor (BJT). The Transistor Tester will vary the voltage at the base of the transistor and measure the current response to create a graph like the one below.+A Transistor Tester is also known as a curve tracer and the Transistor Tester Adapter is used to add curve tracer capability to your set of tools. A Curve Tracer plots the current (I) versus voltage (V) to create an I-V curve for an electronic device.  The Transistor Tester allows you to create I-V curves for a variety of different kinds of transistors and diodes. The Transistor Tester will vary the voltage at the base of the device and measure the current response to create a graph like the one below.
  
 </WRAP> </WRAP>
Line 92: Line 92:
  
  
-In order to perform the analysis on the device under test (DUT) you will need to build a circuit like the one shown below.  In this example, we are using a Fairchild SS8050 Epitaxial Silicon Transistor.  The Transistor Tester Adapter has a 10 kΩ resistor on board for Rb and a 100 Ω resistor on board for Rc.  Connect the C, B, and E points to the Transistor Tester Adapter Connecter J2.+In order to perform the analysis on the device under test (DUT) you will need to build a circuit like the one shown below.  In this example, we are using a Fairchild SS8050 Epitaxial Silicon Transistor.  The Transistor Tester Adapter has a 10 kΩ resistor on board for Rb and a 100 Ω resistor on board for Rc.  Connect the C, B, and E points to the Transistor Tester Adapter Connector J2.
  
 <WRAP group> <WRAP group>
Line 113: Line 113:
 For more information on WaveForms, visit the [[software:waveforms:waveforms-3:reference-manual|WaveForms Reference Manual]].  For more information on WaveForms, visit the [[software:waveforms:waveforms-3:reference-manual|WaveForms Reference Manual]]. 
  
-For technical support, please visit the [[https://forum.digilentinc.com/forum/8-scopes-instruments/|Scopes and Instruments]] section of the Digilent Forums.+For technical support, please visit the [[https://forum.digilentinc.com/forum/8-test-and-measurement/|Test and Measurement]] section of the Digilent Forums.