Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:guides:waveforms-waveform-generator [2022/03/16 02:18] – Keith M Kolmostest-and-measurement:guides:waveforms-waveform-generator [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 125: Line 125:
 --> Analog Discovery Pro (ADP5250) # --> Analog Discovery Pro (ADP5250) #
 <WRAP group> <WRAP column half> <WRAP group> <WRAP column half>
-Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and the scope probe or minigrabbers to the test signal and test signal ground pins on the front of the ADP5250 to create a loopback circuit.  Check the input probe's attenuation factor, as it will be used later to set up the software.+Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and the minigrabbers to the AWG Channel 1  
 +connector on the front of the ADP5250 to create a loopback circuit.  Check the input probe's attenuation factor, as it will be used later to set up the software.
  
 **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.// **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.//
Line 260: Line 261:
 {{section>test-and-measurement:analog-discovery-pro-3x50:change-max-sample-rate&noheader}} {{section>test-and-measurement:analog-discovery-pro-3x50:change-max-sample-rate&noheader}}
  
 +==== Note: Analog Discovery Pro (ADP5250) Wavegen Output Filter ====
 +
 +//The Analog Discovery Pro (ADP5250) features a switchable filter on the AWG output. Click the dropdown below to learn how to use this feature.//
 +
 +--> Enable or Disable the ADP5250's AWG Filter #
 +<WRAP group> <WRAP column half>
 +This filter can be enabled or disabled through the use of the dropdown on the right side of the control toolbar. It can be set to Auto, On, or Off.
 +</WRAP> <WRAP column half>
 +{{:test-and-measurement:guides:filter.jpg?400 |}}
 +</WRAP> </WRAP>
 +<--
 +
 +----
 ==== Note: Using Multiple Instruments ==== ==== Note: Using Multiple Instruments ====
 The //Waveform Generator// instrument can be used with other WaveForms instruments. Using multiple instruments at the same time is helpful in a wide variety of situations. One example would be to use the //Waveform Generator// to stimulate a circuit under test, the //Power Supplies// to provide power to the circuit and view the response with the //Oscilloscope//, all at the same time. More information on how instruments can be operated together can be found in the [[test-and-measurement:guides:waveforms-cross-triggers]] guide. The //Waveform Generator// instrument can be used with other WaveForms instruments. Using multiple instruments at the same time is helpful in a wide variety of situations. One example would be to use the //Waveform Generator// to stimulate a circuit under test, the //Power Supplies// to provide power to the circuit and view the response with the //Oscilloscope//, all at the same time. More information on how instruments can be operated together can be found in the [[test-and-measurement:guides:waveforms-cross-triggers]] guide.
Line 336: Line 350:
 <WRAP group> <WRAP group>
 <WRAP column half> <WRAP column half>
 +
  
 === 3.2 The Preview Plot === === 3.2 The Preview Plot ===