Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:guides:waveforms-oscilloscope [2022/03/04 02:00] – Keith M Kolmostest-and-measurement:guides:waveforms-oscilloscope [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 10: Line 10:
 ===== Prerequisites ===== ===== Prerequisites =====
   * A Digilent Test and Measurement Device with Analog Input and Output Channels:   * A Digilent Test and Measurement Device with Analog Input and Output Channels:
 +    * [[test-and-measurement:analog-discovery-pro-5250:start|Analog Discovery Pro (ADP5250)]] 
     * [[test-and-measurement:analog-discovery-pro-3x50:start|Analog Discovery Pro (ADP3450/ADP3250)]]     * [[test-and-measurement:analog-discovery-pro-3x50:start|Analog Discovery Pro (ADP3450/ADP3250)]]
     * [[test-and-measurement:analog-discovery-studio:start|Analog Discovery Studio]]     * [[test-and-measurement:analog-discovery-studio:start|Analog Discovery Studio]]
Line 113: Line 114:
 </WRAP> </WRAP> </WRAP> </WRAP>
 <-- <--
- +--> Analog Discovery Pro (ADP3450/ADP3250) #
---> Analog Discovery Pro (ADP5250) #+
 <WRAP group> <WRAP column half> <WRAP group> <WRAP column half>
-Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and the scope probe or minigrabbers to the test signal and test signal ground pins on the front of the ADP5250 to create a loopback circuit.  Check the input probe's attenuation factor, as it will be used later to set up the software.+Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and a set of BNC minigrabbers to its Wavegen Out Channel 1 connector. Connect these together, as pictured, to form a loopback circuit. Check the input probe's attenuation factor, as it will be used later to set up the software.
  
 **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.// **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.//
Line 122: Line 122:
 **Note:** //When using BNC Probes, make sure to take note of the probes' bandwidth. When probes are used with an oscilloscope, the achievable bandwidth is limited by both the probes and by the scope. For example, using 1 MHz probes will limit the bandwidth to 1 MHz, even if that is below the Test and Measurement device's specified maximum.// **Note:** //When using BNC Probes, make sure to take note of the probes' bandwidth. When probes are used with an oscilloscope, the achievable bandwidth is limited by both the probes and by the scope. For example, using 1 MHz probes will limit the bandwidth to 1 MHz, even if that is below the Test and Measurement device's specified maximum.//
 </WRAP> <WRAP column half> </WRAP> <WRAP column half>
-{{:test-and-measurement:guides:img_7402.jpg?600 |}}+{{reference:test-and-measurement:guides:wavegen_and_scope.jpg?600}}
 </WRAP> </WRAP> </WRAP> </WRAP>
 <-- <--
---> Analog Discovery Pro (ADP3450/ADP3250) #+ 
 +--> Analog Discovery Pro (ADP5250) #
 <WRAP group> <WRAP column half> <WRAP group> <WRAP column half>
-Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and a set of BNC minigrabbers to its Wavegen Out Channel 1 connector. Connect these together, as pictured, to form a loopback circuit. Check the input probe's attenuation factor, as it will be used later to set up the software.+Connect a BNC oscilloscope probe to the Analog Discovery Pro's Oscilloscope Channel 1 connector and the BNC minigrabbers to the AWG Channel 1 connector on the front of the ADP5250 to create a loopback circuit.  Check the input probe's attenuation factor, as it will be used later to set up the software.
  
 **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.// **Note:** //While BNC Probes are single-ended (as is the Waveform Generator hardware), a connected circuit must still share a common ground with the device. No more than one ground should be connected, in order to avoid the creation of ground loops, which may damage your device.//
Line 133: Line 134:
 **Note:** //When using BNC Probes, make sure to take note of the probes' bandwidth. When probes are used with an oscilloscope, the achievable bandwidth is limited by both the probes and by the scope. For example, using 1 MHz probes will limit the bandwidth to 1 MHz, even if that is below the Test and Measurement device's specified maximum.// **Note:** //When using BNC Probes, make sure to take note of the probes' bandwidth. When probes are used with an oscilloscope, the achievable bandwidth is limited by both the probes and by the scope. For example, using 1 MHz probes will limit the bandwidth to 1 MHz, even if that is below the Test and Measurement device's specified maximum.//
 </WRAP> <WRAP column half> </WRAP> <WRAP column half>
-{{reference:test-and-measurement:guides:wavegen_and_scope.jpg?600}}+{{:test-and-measurement:guides:updated5250scope.jpg?600 |}}
 </WRAP> </WRAP> </WRAP> </WRAP>
 <-- <--
- 
  
 ---- ----