Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:getting-started [2021/05/26 16:41] – ↷ Page name changed from test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:using-guide to test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:getting-started Arthur Browntest-and-measurement:analog-discovery-studio:canvases:interposer-canvas:getting-started [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 3: Line 3:
 {{:reference:test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:interposer5.jpg|}} {{:reference:test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:interposer5.jpg|}}
  
-==== Introduction ==== +===== Introduction ===== 
-This guide explains the use of the Interposer Canvas with the Analog Discovery Studio. The Interposer Canvas is used to host one of our FPGA boards and user designed circuitry.  The interposer Canvas connects to the Analog Discovery Studio through the magnets beneath each of the four standoffs in the corners of the canvas. The Interposer Canvas includes the following features:+This guide explains the use of the Interposer Canvas with the Analog Discovery Studio. The Interposer Canvas is used to host one of our FPGA boards and user-designed circuitry.  The Interposer Canvas connects to the Analog Discovery Studio through the magnets beneath each of the four standoffs in the corners of the canvas. The Interposer Canvas includes the following features:
  
   * One 300 tie-point solderless breadboard   * One 300 tie-point solderless breadboard
Line 14: Line 14:
 ---- ----
  
-====Inventory====+=====Inventory=====
  
   * Interposer Canvas   * Interposer Canvas
Line 23: Line 23:
 ---- ----
  
-====Demonstration====+=====Demonstration=====
  
 ==== 1. Setup ==== ==== 1. Setup ====
Line 101: Line 101:
  
  
 +==== 2. Out of the Box Demo Mode ====
 +<WRAP group>
 +<WRAP column half>
 +== 2.1 ==
 +Each compatible FPGA board comes with an "Out-of-Box" demo programmed into nonvolatile memory, which can be used to show everything is working correctly.  To run this demo, ensure that the programming mode jumper for the board is set to QSPI (or in the case of the Arty A7, just that the jumper is installed) and power the board on. The board will boot, and you will see several LEDs light up. The behavior of the Out-of-Box demo differs depending on the board, so make sure to review the board's documentation for more information on what it does.
 +
 +</WRAP>
 +<WRAP column half>
 +
 +{{:test-and-measurement:analog-discovery-studio:canvases:interposer-canvas:img_5852.png?600|}}
 +</WRAP>
 +</WRAP>
 +----
 +===== Next Steps =====
 +
 +For more guides on how to use your Analog Discovery Studio device, check out its resource center: [[test-and-measurement:analog-discovery-studio:start]].
 +
 +To find more information on the Interposer canvas, and for links to the resource centers for the various compatible FPGA development boards, check out the Interposer Canvas's [[start|Resource Center]].
 +
 +For more information on WaveForms, visit the [[software:waveforms:waveforms-3:reference-manual|WaveForms Reference Manual]]. 
 +
 +For technical support, please visit the [[https://forum.digilentinc.com/forum/8-test-and-measurement/|Test and Measurement]] section of the Digilent Forums.
 +
 +{{tag>analog-discovery-studio tutorial analog-discovery-canvas canvas}}