Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:analog-discovery-pro-5250:specifications [2022/02/21 17:58] – CLK0/CLK1 not supported Arthur Browntest-and-measurement:analog-discovery-pro-5250:specifications [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 6: Line 6:
 ==== Analog Input Channels ==== ==== Analog Input Channels ====
  
-Supports the Oscilloscope, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.+Supports the Oscilloscope, Data Logger, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.
  
 === Vertical System === === Vertical System ===
Line 25: Line 25:
  
 |<100% 25%>| |<100% 25%>|
-^ Maximum Sampling Rate | 1 GS/s single channel, 500 MS/s per channel, dual channel ||+^ Maximum Sampling Rate | 1 GS/s single channel \\ 500 MS/s per channel, dual channel ||
 ^ Maximum Record Length | 1 MS per channel || ^ Maximum Record Length | 1 MS per channel ||
  
Line 81: Line 81:
 ^ Number of Channels                                     || 1                                                | ^ Number of Channels                                     || 1                                                |
 ^ Output Impedance                                       || 50 Ω                                             | ^ Output Impedance                                       || 50 Ω                                             |
 +^ Switchable Filter                                      || 36 MHz lowpass, 7-pole, elliptical               |
 ^ Sine    ^ Maximum Frequency                             | 20 MHz                                           | ^ Sine    ^ Maximum Frequency                             | 20 MHz                                           |
 ^ :::     ^ Total Harmonic Distortion (1 MHz)             | -55 dBc                                          | ^ :::     ^ Total Harmonic Distortion (1 MHz)             | -55 dBc                                          |
Line 321: Line 322:
 ---- ----
 ===== Power Requirements ===== ===== Power Requirements =====
-|<100% 25%> +|<100% 25%>| 
-  +^ Voltage Input Range | 100 V AC to 240 V AC, ±10%, 50/60 Hz ||
-^ Voltage Input Range | 100 V AC to 240 V AC, 50/60 Hz ||+
 ^ Power Consumption | 100 W maximum || ^ Power Consumption | 100 W maximum ||
 ^ Power Input Connector | IEC C13 power connector ||  ^ Power Input Connector | IEC C13 power connector || 
Line 346: Line 346:
  
 ==== DMM Isolation Voltages (Ground to Earth) ==== ==== DMM Isolation Voltages (Ground to Earth) ====
 +
 +<columns 100% 5% 95%>
 +{{:test-and-measurement:analog-discovery-pro-5250:hazard.png?40}}
 +<newcolumn>
 +**Hazardous Voltage:** This icon denotes a warning advising you to take precautions to avoid electrical shock.
 +</columns>
 +
 +=== Channel-to-earth Ground ===
 |<100% 25%>| |<100% 25%>|
 ^ Continuous | 300 V, Measurement Category II || ^ Continuous | 300 V, Measurement Category II ||
Line 353: Line 361:
  
 Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe. Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe.
 +
 +<columns 100% 5% 95%>
 +{{:test-and-measurement:analog-discovery-pro-5250:caution.png?40}}
 +<newcolumn>
 +**Caution:** Do not connect the ADP5250 hardware to signals or use for measurements within Measurement Categories III or IV.
 +</columns>
  
 ==== DC Power Supply Isolation Voltages ==== ==== DC Power Supply Isolation Voltages ====
 |<100% 25%>| |<100% 25%>|
-^ +25V and -25V to earth ground, continuous | 60VDC, Measurement Category 1 |||+^ +25V and -25V to earth ground, continuous | 60 VDC, Measurement Category 1 ||| 
 + 
 +**Note:** //Measurement Categories CAT I and CAT O (Other) are equivalent. The input circuits are not intended for direct connection to the MAINs building installations of Categories CAT II, CAT III, or CAT IV.//
  
 ---- ----
Line 380: Line 396:
  
 ---- ----
- +{{page>test-and-measurement:analog-discovery-pro-5250:certifications&fullpage&noindent}}
-==== Safety ==== +
-This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:  +
-  * IEC 61010-1, EN 61010-1  +
-  * UL 61010-1, CSA 61010-1  +
- +
----- +
- +
-==== Electromagnetic Compatibility ==== +
- +
-This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use; for radio equipment; and for telecommunication terminal equipment:  +
-  * EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity   +
-  * EN 55011 (CISPR 11): Group 1, Class A emissions  +
-  * EN 55022 (CISPR 22): Class A emissions  +
-  * EN 55024 (CISPR 24): Immunity  +
-  * AS/NZS CISPR 11: Group 1, Class A emissions  +
-  * AS/NZS CISPR 22: Class A emissions  +
-  * FCC 47 CFR Part 15B: Class A emissions  +
-  * ICES-001: Class A emissions  +
- +
-**Note:** In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.  +
- +
-**Note:** Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.  +
- +
-**Note:** For EMC declarations and certifications, and additional +
- +
- +
----- +
- +
-====CE Compliance==== +
-This product meets the essential requirements of applicable European Directives, as follows:  +
-  * 2014/35/EU; Low-Voltage Directive (safety)  +
-  * 2014/30/EU; Electromagnetic Compatibility Directive (EMC)  +