Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
test-and-measurement:analog-discovery-pro-5250:specifications [2022/02/03 19:06] – Fix line breaks Arthur Browntest-and-measurement:analog-discovery-pro-5250:specifications [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
-====== Analog Discovery Pro ADP5250 Specifications ======+====== Analog Discovery Pro (ADP5250) Specifications ======
 ~~TechArticle~~ ~~TechArticle~~
 These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted. These specifications are valid following 30 minutes of warmup and are typical at 25 °C unless otherwise noted.
Line 6: Line 6:
 ==== Analog Input Channels ==== ==== Analog Input Channels ====
  
-Supports the Oscilloscope, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.+Supports the Oscilloscope, Data Logger, Spectrum Analyzer, Network Analyzer, Impedance Analyzer, and Script Editor instruments.
  
 === Vertical System === === Vertical System ===
Line 14: Line 14:
 ^ Bandwidth (-3 dB) | 100 MHz || ^ Bandwidth (-3 dB) | 100 MHz ||
 ^ Resolution | 8 bits || ^ Resolution | 8 bits ||
-^ Accuracy | ± 2% of input ±1% full scale (V peak to peak) || +^ Accuracy | ±2% of input ±1% full scale (V peak to peak) || 
-^ Input coupling | AC, DC ||+^ Input Coupling | AC, DC ||
 ^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)|| ^ Vertical Sensitivity (range) | 10 mV / div (100 mV peak to peak) \\ 20 mV / div (200 mV peak to peak) \\ 50 mV / div (400 mV peak to peak) \\ 100 mV / div (1 V peak to peak) \\ 200 mV / div (2 V peak to peak) \\ 500 mV / div (4 V peak to peak) \\ 1 V / div (10 V peak to peak) \\ 2 V / div (20 V peak to peak) \\ 5 V / div (40 V peak to peak)||
-^ Input impedance | 1 MΩ \\ 20 pF || +^ Input Impedance | 1 MΩ ││ 20 pF || 
-^ Acquisition modes | Sample, peak detect, averaging || +^ Acquisition Modes | Sample, peak detect, averaging || 
-^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/div - ±5 V \\ 100 mV/div, 200 mV/div, 50 mV/div, 1 V/div, 2 V/div, 5 V/div - ±20 V || +^ DC Offset Range | 10 mV/div, 20 mV/div, 50 mV/div ranges: ±5 V \\ 100 mV/div, 200 mV/div, 50 mV/div, 1 V/div, 2 V/div, 5 V/div ranges: ±20 V ||
  
 ---- ----
 === Horizontal System === === Horizontal System ===
  
-|<100% 40%>| +|<100% 25%>| 
-^ Maximum sampling rate | 1 GS/s single channel, 500 MS/s/channel, dual channel || +^ Maximum Sampling Rate | 1 GS/s single channel \\ 500 MS/s per channel, dual channel || 
-^ Maximum record length | 1 MS / channel ||+^ Maximum Record Length | 1 MS per channel ||
  
 ---- ----
 ==== Digital Channels / Logic Analyzer ==== ==== Digital Channels / Logic Analyzer ====
 +Supports the Logic Analyzer and Script Editor instruments.
  
 {{ :test-and-measurement:analog-discovery-pro-5250:connector.png?400 |}} {{ :test-and-measurement:analog-discovery-pro-5250:connector.png?400 |}}
- 
- 
  
 === Vertical System === === Vertical System ===
-|<100% 40%> +|<100% 40%>| 
-^ Number of channels | 34 ||+^ Number of Channels | 34 [(At time of writing, WaveForms software does not support use of the CLK0/CLK1 lines. All 32 DIO pins are fully supported.)] ||
 ^ Maximum Input Frequency | 100 MHz || ^ Maximum Input Frequency | 100 MHz ||
-^ Input voltage | 0V to 5V || +^ Input Voltage | 0 V to 5 V || 
-^ Input current | ≤ 50 µA || +^ Input Current | ≤50 µA || 
-^ Input threshold | Programmable, 0V to 2.0V ||+^ Input Threshold | Programmable, 0 V to 2.0 V ||
 ^ Threshold Accuracy | 350 mV || ^ Threshold Accuracy | 350 mV ||
-^ Input Impedance | 100 kΩ \\ 7.5 pF pulled to -2.0V to +6.5V, varies with input threshold setting || +^ Input Impedance | 100 kΩ ││ 7.5 pF pulled to -2.0 V to +6.5 V, varies with input threshold setting || 
-^ Additional / Internal channels | Digital I/O lines, function generator start, external trigger (TRIG), power line frequency ||+^ Additional / Internal Channels | Digital I/O lines, function generator start, external trigger (TRIG), power line frequency ||
  
 **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. **Note:** Mixed signal oscilloscope digital channels are designed to withstand accidental overvoltage from signals on the ADP5250. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation.
 +
 +~~REFNOTES~~
  
 === Horizontal System === === Horizontal System ===
-|<100% 40%> +|<100% 40%>| 
- +^ Timing Mode Sample Rate | 1 GS/s (down to ~15 kS/s) || 
-^ Timing mode sample rate | 1 GS/s (down to ~15 kS/s) || +^ Maximum External Sample Clock Rate | 100 MHz ||
-^ Maximum external sample clock rate | 100 MHz ||+
 ^ Record Length (Typical) | 1 MS || ^ Record Length (Typical) | 1 MS ||
 ^ Record Length (Minimum) | 4 kS || ^ Record Length (Minimum) | 4 kS ||
-^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is in an integer || +^ Decimation | External Sample Clock, 1:1, 2:1, and n*4:1 where n is an integer || 
-^ Maximum Sample Compression | 2^15 to 1 ||+^ Maximum Sample Compression | 2<sup>15</sup> to 1 ||
  
 ---- ----
  
-=== Triggering === +==== Triggering ==== 
- +|<100% 20% 20%>| 
-|<100% 40%> +^ Trigger Modes                                      || Normal, Auto, Force, Single               | 
-^ Trigger modes | Normal, Auto, Force, Single || +^ Trigger Sources                                    || Oscilloscope analog channels \\ Oscilloscope digital channels \\ Function generator start \\ Digital I/O lines \\ External trigger (TRIG) \\ Power line frequency | 
-^ Trigger sources | Oscilloscope analog channels \\ Oscilloscope digital channels \\ Function generator start \\ Digital I/O lines \\ External trigger (TRIG) \\ Power line frequency || +^ Trigger Types      ^ Analog                         | Edge with hysteresis                      | 
-^ Trigger Types | || +^ :::                ^ Digital                        | Edge, pattern, glitch, level              | 
-^   Analog | Edge with hysteresis || +^ Trigger Resolution ^ Analog / Oscilloscope          | 667 ps                                    | 
-^   Digital | Edge, pattern, glitch, level || +^ :::                ^ Digital / Logic Analyzer       | 1 ns                                      | 
-^ Trigger Resolution | || +^ Trigger Export                                     || Available through external trigger (TRIG) |
-^   Analog / oscilloscope | 667 ps || +
-^   Digital / logic analyzer | 1 ns || +
-^   Trigger Export | Available external trigger (TRIG) ||+
  
 ---- ----
  
-=== Waveform Generator (WaveGen) === +===== Waveform Generator (WaveGen) ===== 
-|<100% 40%>+Supports the Waveform Generator, Network Analyzer, Impedance Analyzer, and Script Editor instruments.
  
-^ Waveforms                           | Sine, square, ramp / triangle, DC, arbitrary     || +|<100% 25% 25%>| 
-^ Update rate                         | 125 M Samples / s                                || +^ Waveforms                                              || Sine, square, ramp / triangle, DC, arbitrary     | 
-^ Resolution                          | 14 bits                                          || +^ Update Rate                                            || 125 MS/s                                         | 
-^ Number of channels                  | 1                                                || +^ Resolution                                             || 14 bits                                          | 
-^ Output impedance                    | 50 Ω                                             || +^ Number of Channels                                     || 1                                                | 
-^ Sine                                |                                                  || +^ Output Impedance                                       || 50 Ω                                             | 
-^                   Maximum frequency | 20 MHz                                           || +^ Switchable Filter                                      || 36 MHz lowpass, 7-pole, elliptical               | 
-^   Total Harmonic Distortion (1 MHz) | - 55 dBc                                         || +^ Sine    ^ Maximum Frequency                             | 20 MHz                                           | 
-^  Total Harmonic Distortion (10 MHz) | -50 dBc                                          || +^ :::     ^ Total Harmonic Distortion (1 MHz)             | -55 dBc                                          | 
-^  Spurious Free Dynamic Range (SFDR) | - 70 dB at 1 MHz (non-harmonic)                  || +^ :::     ^ Total Harmonic Distortion (10 MHz)            | -50 dBc                                          | 
-^                 Phase noise (1 MHz) | -115 dBc/Hz at 10 kHz offset                     || +^ :::     ^ Spurious Free Dynamic Range (SFDR)            | -70 dB at 1 MHz (non-harmonic)                   | 
-^ Square                              |                                                  || +^ :::     ^ Phase Noise (1 MHz)                           | -115 dBc/Hz at 10 kHz offset                     | 
-^                   Maximum frequency | 5 MHz                                            || +^ Square  ^ Maximum Frequency                             | 5 MHz                                            | 
-^                    Rise / Fall time | <20ns (10% to 90%)                               || +^ :::     ^ Rise / Fall Time                              | <20 ns (10% to 90%)                              | 
-^                           Overshoot | <5%                                              || +^ :::     ^ Overshoot                                     | <5%                                              | 
-^                              Jitter | 8ns cycle-to-cycle                               || +^ :::     ^ Jitter                                        | 8 ns cycle-to-cycle                              | 
-^ Ramp / Triangle maximum frequency   | 1 MHz                                            || +^ Ramp / Triangle Maximum Frequency                      || 1 MHz                                            | 
-^ Accuracy (with 10 kΩ load)          |                                                  || +^ Accuracy (with >10 kΩ load)  ^ Amplitude (1 kHz sine)   | ±(1% of output value ±5 mV)                      | 
-^              Amplitude (1 kHz sine) | ±(1% of output value ± 5mV)                      || +^ :::                          ^ DC                       | ±(1% of output value ±7.5 mV)                    | 
-^                                  DC | ±(1% of output value ± 5mV)                      || +^ Output Range                 ^ 50 Ω                     | ±6 V                                             | 
-^ Output range                        |                                                  || +^ :::                          ^ Hi-Z (>10 kΩ)            | ±12 V                                            | 
-^                                50 Ω | ± 6V                                             || +^ DC Offset                    ^ 50 Ω                     | ±6 V                                             | 
-^                      Hi-Z (> 10 kΩ) | ± 12V                                            || +^ :::                          ^ Hi-Z (>10 kΩ)            | ±12 V                                            | 
-^ DC offset                           |                                                  || +^ Frequency                    ^ Accuracy                 | ≤100 ppm                                         | 
-^                                50 Ω | ± 6V                                             || +^ :::                          ^ Resolution               | 1 µHz                                            | 
-^                      Hi-Z (> 10 kΩ) | ± 12V                                            || +^ Arbitrary Waveforms          ^ Points                   | 1 MS                                             | 
-^ Frequency                           |                                                  || +^ :::                          ^ Sample Rate              | 125 MS/s                                         | 
-^                            Accuracy | ≤ 100 ppm                                        || +^ Protection                                             || Short-circuit protected                          |
-^                          Resolution | 1 µHz                                            || +
-^ Arbitrary Waveforms                 |                                                  || +
-^                              Points | 1 MS                                             || +
-^                         Sample rate | 125 MS/s                                         || +
-^ Protection                          | Short-circuit protected                          ||+
  
 **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output. **Note:** The combination of signal amplitude and DC offset cannot exceed the output range specifications. The impedances listed are the loads applied by the user to the Waveform Generator output.
Line 119: Line 110:
 {{ :test-and-measurement:analog-discovery-pro-5250:connector2.png?400 |}} {{ :test-and-measurement:analog-discovery-pro-5250:connector2.png?400 |}}
  
-=== Digital I/O === +===== Digital I/O ===== 
-|<100% 40%>+Supports the Static I/O and Script Editor instruments.
  
-^ Number of channels | 8 || +|<100% 40%>| 
-^ Direction control | Input or output, software-selectable || +^ Number of Channels | 8 || 
-^ Logic Level | 5V compatible TTL input \\ 3.3V LVTTL output || +^ Direction Control | Input or output, software-selectable || 
-^ Drive strength | 4 mA || +^ Logic Level | 5 V compatible TTL input \\ 3.3 V LVTTL output || 
-^ Input Voltage | 0 to 5V || +^ Drive Strength | 4 mA || 
-^ DIO channel pull resistors | 10 kΩ, pull-down on dig/<0..7> \\ 10 kΩ, configurable pull-up to 3.3 V on dig/<6,7> ||+^ Input Voltage | 0 to 5 V || 
 +^ DIO Channel Pull Resistors | 10 kΩ, pull-down on dig/<0..7> \\ 10 kΩ, configurable pull-up to 3.3 V on dig/<6,7> ||
  
 **Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation. **Note:** Digital I/O lines are designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. They are not recommended for use with signals likely to exceed 0 V to 5 V in normal operation.
- 
-**Note:** CLK0 & CLK0 are only available with the Virtualbench software. 
 ---- ----
  
-===Digital Supply=== +====Digital Power Supply==== 
-|<100% 40%> +|<100% 40%>| 
- +^ Voltage | 3.3 V ± 10% | 
-^ 3.3 V output | ||  +^ Current | 20 mA |
-^   Voltage | 3.3 V ±10% ||  +
-^   Current | 20 mA ||+
  
 ---- ----
-=== DC Power Supply ===+===== Digital Multimeter ===== 
 +|<100% 40%>| 
 +^ Functions        | DC Voltage, AC Voltage, DC current, AC current, resistance, diode, continuity || 
 +^ Resolution       | 5½ digits                                                                     || 
 +^ Sample Rate      | 5 S/s                                                                         ||
  
 +**Caution:** Do not use this device for connection to signals or for measurements within Measurement Categories III or IV. For more information about Measurement Categories, refer to the [[#safety_voltages|Safety Voltages]] section.
  
-^ Outputs | || +=== Input Protection ===
-^   0 V to +6 V | 0 A to 1 A || +
-^   0 V to +25 V | 0 mA to 500 mA (isolated) || +
-^   0 V to -25 V | 0 mA to 500 mA (isolated) ||+
  
-**Note:**  the +25 V and – 25 V channels are bank isolated from ground but not from each other. +|<100% 20% 25%>| 
- +^ Resistance, Diode || Up to 300 V DC                                 | 
----- +^ DC and AC Voltage || Up to 300 V DC or 265 V AC (rms) 400 V AC (peak) | 
-=== Digital Multimeter === +^ DC and AC Current ^ DMM A Current Connector Fuse  | Internal ceramic fuse, 10 A 250 V, time-delay, 5 x 20 mm, T 10A H 250V (Bussman part number D505H-10-R at www.cooperindustries.com)       | 
-|<100% 40%> +^ :::               ^ DMM mA Current Connector Fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) |
- +
-^ Functions | DC Voltage, AC Voltage, DC current, AC current, resistance, diode, continuity || +
-^ Resolution | 5½ digits || +
-^ Sample rate | 5 S/s || +
-^ Input protection | || +
-^   Resistance, diode | Up to 300V DC || +
-^   DC and AC voltage | Up to 300V DC or 265 VAC(rms) 400 V AC (peak) || +
-^ DC and AC current | || +
-^   DMM A current connector fuse | Internal ceramic fuse, 10 A 250 V, time-delay, 5 x 20 mm, T 10A H 250V (Bussman part number D505H-10-R at www.cooperindustries.com) || +
-^ DMM mA current connector fuse | Internal ceramic fuse, 1.25 A 250 V, time-delay, 5 x 20 mm, T 1.25A H 250V (Bussman part number S505H-1.25-R at www.cooperindustries.com) || +
-^ Maximum common-mode voltage | 300 V DC or AC (rms) || +
- +
-**Caution:** Do not use this device for connection to signals or for measurements within Measurement Categories III or IV. For more information about Measurement Categories, refer to the Safety Voltages section.+
  
 **Caution:** Fuses are located on bottom of device underneath door. Use Phillips #1 screwdriver for removal. Ensure all hazardous voltages are disconnected from the device prior to removal of door. **Caution:** Fuses are located on bottom of device underneath door. Use Phillips #1 screwdriver for removal. Ensure all hazardous voltages are disconnected from the device prior to removal of door.
  
 **Fuse:** When the fuse symbol is marked on a device, take proper precautions. **Fuse:** When the fuse symbol is marked on a device, take proper precautions.
 +
 +|<100% 40%>|
 +^ Maximum common-mode voltage | 300 V DC or AC (rms) ||
  
 ---- ----
Line 178: Line 158:
  
 === DC Voltage Accuracy === === DC Voltage Accuracy ===
-|<100% 25%>+|<100% 25%>|
 ^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ^ **Range** | **Input Impedance** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient
 ±(% of Reading + % of Range)/C°** || ±(% of Reading + % of Range)/C°** ||
 ^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 || ^ 100 mV* | <10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 ||
-^ 1 V | > 10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 ||+^ 1 V | >10 GΩ, 10 MΩ | 0.015 + 0.005 | 0.001 + 0.0005 ||
 ^ 10 V | >10 GΩ, 10 MΩ | 0.015  +0.005 | 0.001 + 0.0005 || ^ 10 V | >10 GΩ, 10 MΩ | 0.015  +0.005 | 0.001 + 0.0005 ||
 ^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 || ^ 100 V | 10 MΩ | 0.035 + 0.005 | 0.001 + 0.0005 ||
Line 190: Line 170:
 ---- ----
 === DC Current Accuracy === === DC Current Accuracy ===
-|<100% 25%> +|<100% 25%>| 
- +^ **Range** | **Burden Voltage** | **1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient
-^ **Range** | **Burden Voltage** | **1-Year Accuracy**| ** ±(% of Reading + % of Range)** | ** Temperature Coefficient+
 ±(% of Reading + % of Range)/C° ** || ±(% of Reading + % of Range)/C° ** ||
 ^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 || ^ 10 mA | <0.03 V | 0.070 + 0020 | 0.0035 + 0.0010 ||
Line 199: Line 178:
 ^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 || ^ 10 A* | <0.3 V | 0.130 + 0.004 | 0.0045 + 0.0010 ||
  
-* 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2A. After measuring >5 A,+* 30 seconds on, 30 seconds off. Add 300 ppm for currents >2.2 A. After measuring >5 A,
 Wait two minutes to get full accuracy in the 1 A range. Wait two minutes to get full accuracy in the 1 A range.
  
 ---- ----
 === DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage === === DC Resistance Accuracy (2-Wire)*, 1V Open Circuit Voltage ===
-|<100% 25%> +|<100% 25%>|
- +
 ^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient ^ **Range** | **Short-Circuit Current** | **1-Year Accuracy ±(% of Reading + % of Range) ** | ** Temperature Coefficient
 ±(% of Reading + % of Range)/C° ** ||  ±(% of Reading + % of Range)/C° ** || 
Line 222: Line 199:
 **Caution:**  The input terminals of the DMM are not protected for electromagnetic interference. As a result, the DMM may experience reduced measurement accuracy or other temporary performance degradation when connected to unshielded test leads in an environment with radiated or conducted radio frequency electromagnetic interference. **Caution:**  The input terminals of the DMM are not protected for electromagnetic interference. As a result, the DMM may experience reduced measurement accuracy or other temporary performance degradation when connected to unshielded test leads in an environment with radiated or conducted radio frequency electromagnetic interference.
  
-|<100% 25%> +|<100% 25%>| 
-^ DC continuity accuracy range | 100 Ω || +^ DC Continuity Accuracy Range | 100 Ω || 
-^ DC diode test range | 2 V ||+^ DC Diode Test Range | 2 V ||
 ^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB || ^ Effective Common-Mode Rejection-Mode Ratio (CMRR), 1 kΩ resistance in LO lead | >100 dB ||
-^ Normal-Mode rejection Ratio (NMRR), 50/60 Hz ±0.1% | >100 dB ||  +^ Normal-Mode Rejection Ratio (NMRR), 50/60 Hz ± 0.1% | >100 dB ||  
-^ Overrange | 105% of range except300 V || +^ Overrange | 105% of range except 300 V || 
  
 ---- ----
Line 233: Line 210:
  
 ===AC Voltage Accuracy=== ===AC Voltage Accuracy===
-|<100% 25%> +|<100% 25%>|
 ^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/C°**|| ^ **Range (rms)** | **Peak Voltage**| **Frequency** | ** 1-Year Accuracy ±(% of Reading + % of Range)**|**Temperature Coefficient ±(% of Reading + % of Range)/C°**||
 ^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 || ^ 100 mV, 1 V, 10 V, 100 V, 265 V | ±210 mV, ±2.1 V, ±21 V, ±210 V, ±400 V | 20 Hz to 45 Hz | 0.91 + 0.10 | 0.01 + 0.005 ||
-^ | | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || +^ ::: | ::: | 45 Hz to 65 Hz | 0.30 + 0.05 | 0.01 + 0.005 || 
-^ | | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || +^ ::: | ::: | 65 Hz to 1 kHz | 0.21 + 0.05 | 0.01 + 0.005 || 
-^ | | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || +^ ::: | ::: | 1 kHz to 5 kHz | 0.12 + 0.05 | 0.01 + 0.005 || 
-^ | | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 ||+^ ::: | ::: | 5 kHz to 20 kHz | 0.35 + 0.05 | 0.01 + 0.005 ||
  
 ---- ----
 ===AC Current Accuracy=== ===AC Current Accuracy===
-|<100% 25%> +|<100% 25%>|
 ^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** || ^ **Range**|** Short-Circuit Current**| **Burden Voltage (rms)**| **Frequency**| ** 1-Year Accuracy ±(% of Reading + % of Range)** | ** Temperature Coefficient ±(% of Reading + % of Range)/C° ** ||
 ^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 || ^ 5 mA | ±10.5 mA | <0.02 | 20 Hz to 1 kHz | 0.20 + 0.01 | 0.01 + 0.005 ||
Line 255: Line 230:
 ^ 5 A | ±1.05 A | <0.02 V | 20 Hz to 1 kHz | 0.25 + 0.03 | 0.01 + 0.005 || ^ 5 A | ±1.05 A | <0.02 V | 20 Hz to 1 kHz | 0.25 + 0.03 | 0.01 + 0.005 ||
 ^ 5 A | ±1.05 A | <0.02 V | 1 kHz to 5 kHz | 0.60 + 0.03 | 0.01 + 0.005 || ^ 5 A | ±1.05 A | <0.02 V | 1 kHz to 5 kHz | 0.60 + 0.03 | 0.01 + 0.005 ||
 +
 +----
 +===== DC Power Supply =====
 +
 +^ Outputs | 0 V to +6 V | 0 A to 1 A ||
 +^ :::     | 0 V to +25 V | 0 mA to 500 mA (isolated) ||
 +^ :::     | 0 V to -25 V | 0 mA to 500 mA (isolated) ||
 +
 +**Note:**  the +25 V and –25 V channels are bank isolated from ground but not from each other.
 +
  
 ---- ----
 === DC Accuracy / Resolution === === DC Accuracy / Resolution ===
-|<100% 25%> +|<100% 25%>| 
- +^ **Output** | ** Type ** | ** +6 V **| **+25 V**|**-25 V**|| 
-^ **Output** | ** Type ** | ** +6V **| **+25V**|**-25V**|| +^ DC Output | Voltage | 0 V to +6 V | 0 V to +25 V | 0 V to -25 V || 
-^ DC output | Voltage | 0 V to +6 V | 0 V to +25 V | 0 V to -25 V || +^ :::       | Current | 1 A | 500 mA | 500 mA || 
-^ DC output | Current | 1 A | 500 mA | 500 mA || +^ Programming Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || 
-^ Programming accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.1% + 20 mV | 0.1% + 20 mV || +^ :::                                            | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || 
-^ Programming accuracy, ±(% of reading + offset) | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA || +^ Readback Accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.15% + 20 mV | 0.15% + 20 mV || 
-^ Readback accuracy, ±(% of reading + offset) | Voltage | 0.1% + 5 mV | 0.1% + 20 mV | 0.1% + 20 mV || +^ :::                                         | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15% + 4 mA ||
-^ Readback accuracy, ±(% of reading + offset) | Current | 0.2% + 10 mA | 0.15% + 4 mA | 0.15 + 4 mA ||+
 ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV || ^ Programming Resolution | Voltage | 1.7 mV | 6.5 mV | 6.5 mV ||
-^ Programming Resolution | Current | 0.30 mA | 0.15 mA | 0.15 mA || +^ :::                    | Current | 0.30 mA | 0.15 mA | 0.15 mA || 
-^ Readback resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || +^ Readback Resolution | Voltage | 0.41 mV | 1.7 mV | 1.7 mV || 
-^ Readback resolution | Current | 70 µA | 35 µA | 35 µA || +^ :::                 | Current | 70 µA | 35 µA | 35 µA || 
-^ Load regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV ||+^ Load Regulation ±(% of reading + offset) | Voltage | 0.01% + 25 mV | 0.03% + 5 mV | 0.03% + 5 mV ||
  
  
-|<100% 25%> +|<100% 25%>|  
-  +^ Overvoltage Protection | 30 V (25 V channels) and 10 V (6 V channel) || 
-^ Overvoltage protection | 30 V (25 V channels) and 10 V (6 V channel) || +^ Reverse Voltage Protection | Reverse clamp diode, protected by self-resetting fuse ||
-^ Reverse voltage protection | Reverse clamp diode, protected by self-resetting fuse ||+
  
 ---- ----
-=== External Trigger (TRIG) ===+===== External Trigger (TRIG) =====
  
-|<100% 25%> +|<100% 25%>| 
- +^ Direction Control | Input or output, software-selectable ||
-^ Direction control | Input or output, software-selectable ||+
 ^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output || ^ Logic Level | 5 V compatible TTL input, 3.3 V LVLTTL output ||
-^ Drive strength | 4 mA || +^ Drive Strength | 4 mA || 
-^ Input voltage | 0 V to 5 V ||+^ Input Voltage | 0 V to 5 V ||
  
-**Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed 5 V to 5 V in normal operation.+**Note:** The external trigger line is designed to withstand accidental overvoltage from signals on the ADP5250 or similar devices. It is not recommended for use with signals likely to exceed 0 V to 5 V in normal operation.
  
 ---- ----
-==== Features ====+===== Features =====
  
-=== Spectrum Analyzer ===+==== Spectrum Analyzer ====
  
-|<100% 25%>+|<100% 25%>|
 ^ Frequency Range | DC to maximum bandwidth of scope || ^ Frequency Range | DC to maximum bandwidth of scope ||
-^ Display modes |Magnitude, average, peak hold, min hold, count || +^ Display Modes |Magnitude, average, peak hold, min hold, count || 
-^ Y axis | Logarithmic (dbV, dBu, dBm,) or linear (volts) ||  +^ Y Axis | Logarithmic (dbV, dBu, dBm) or linear (volts) ||  
-^ X axis | Linear or logarithmic ||  +^ X Axis | Linear or logarithmic ||  
-^ Windowing functions | Rectangular, Triangular, Hamming, Hann, Cosine, Blackman-Harris, Flat Top, Kaiser ||+^ Windowing Functions | Rectangular, Triangular, Hamming, Hann, Cosine, Blackman-Harris, Flat Top, Kaiser ||
  
 ---- ----
-=== Network Analyzer === +==== Network Analyzer ==== 
-|<100% 25%> +|<100% 25%>| 
- +^ Frequency Range | 1 mHz to 10 MHz, up to 10k samples per decade ||  
- +^ Display Modes | Magnitude, Phase || 
-^ Frequency Range | 1 mHz to 10MHz, up to 10k samples per decade ||  +^ Y Axis | Linear or logarithmic || 
-^ Display modes | Magnitude, Phase || +^ X Axis | Linear or logarithmic ||
-^ Y axis | Linear or logarithmic || +
-^ X axis | Linear or logarithmic ||+
 ^ Plots | Time, FFT, Nichols, Nyquist || ^ Plots | Time, FFT, Nichols, Nyquist ||
  
 ---- ----
-=== Math Channels === +==== Math Channels ====
- +
-|<100% 25%>+
  
 +|<100% 25%>|
 ^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. || ^ Operations | addition “+”, subtraction “-”, multiplication “*”, division “/”, reminder “%”. ||
 ^ Brackets | parentheses (), square brackets [] || ^ Brackets | parentheses (), square brackets [] ||
Line 326: Line 305:
  
 ---- ----
-=== Automatic Measurements (analog channels only) ===+==== Automatic Measurements (Analog Channels Only) ====
  
-|<100% 25%> +|<100% 25%>| 
- +^ Oscilloscope Mode | DC to maximum bandwidth of scope || 
-^ Oscilloscope mode | DC to maximum bandwidth of scope || +^ Spectrum Mode | Magnitude, average, peak hold, min hold, count ||
-^ Spectrum mode | Magnitude, average, peak hold, min hold, count ||+
 ^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) || ^ Statistics | Logarithmic (dbV, dBu, dBm,) or linear (volts) ||
  
 ---- ----
-==== Connectivity ====+===== Connectivity =====
  
-=== Wired USB Interface ===+==== Wired USB Interface ====
  
-|<100% 25%> +|<100% 25%>| 
-^ USB specification | USB 2.0 Hi-Speed ||+^ USB Specification | USB 2.0 Hi-Speed ||
  
 ---- ----
-==== Power Requirements ==== +===== Power Requirements ===== 
-|<100% 25%> +|<100% 25%>| 
-  +^ Voltage Input Range | 100 V AC to 240 V AC, ±10%, 50/60 Hz || 
-^ Voltage input range | 100 VAC to 240 VAC, 50/60 Hz || +^ Power Consumption | 100 W maximum || 
-^ Power consumption | 100 W maximum || +^ Power Input Connector | IEC C13 power connector ||  
-^ Power input connector | IEC C13 power connector ||  +^ Power Disconnect | The AC power cable provides main power disconnect. Do not position the equipment so that it is difficult to disconnect the power cable. Depressing the front panel power button does not inhibit the internal power supply. ||
-^ Power disconnect | The AC power cable provides main power disconnect. Do not position the equipment so that it is difficult to disconnect the power cable. Depressing the front panel power button does not inhibit the internal power supply. ||+
  
 ---- ----
-==== Physical Characteristics ====+===== Physical Characteristics =====
  
-|<100% 25%>+|<100% 25%>|
 ^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) || ^ Enclosure | 25.40 cm x 19.05 cm x 7.77 cm \\ (10.00 in x 7.50 in x 3.06 in) ||
 ^ Weight | 2.05 kg (4 lb 8.3 oz) || ^ Weight | 2.05 kg (4 lb 8.3 oz) ||
-^ Security cable slot | 1, complies with Kensington security slot dimensions ||+^ Security Cable Slot | 1, complies with Kensington security slot dimensions ||
  
 ---- ----
Line 365: Line 342:
 **Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling. **Note:** Use the ADP5250 in a horizontal orientation. Allow at least 10.16 cm (4.0 in.) of clearance in front and behind the ADP5250 for USB, power, and common connector cabling.
  
-==== Safety Voltages ====+===== Safety Voltages =====
 Connect only voltages that are within these limits. Connect only voltages that are within these limits.
  
-=== DMM Isolation Voltages (Ground to Earth) === +==== DMM Isolation Voltages (Ground to Earth) ==== 
-|<100% 25%>+ 
 +<columns 100% 5% 95%> 
 +{{:test-and-measurement:analog-discovery-pro-5250:hazard.png?40}} 
 +<newcolumn> 
 +**Hazardous Voltage:** This icon denotes a warning advising you to take precautions to avoid electrical shock. 
 +</columns> 
 + 
 +=== Channel-to-earth Ground === 
 +|<100% 25%>|
 ^ Continuous | 300 V, Measurement Category II || ^ Continuous | 300 V, Measurement Category II ||
 ^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test || ^ Withstand | 3000 V (RMS), verified by a 5 s dielectric withstand test ||
Line 377: Line 362:
 Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe. Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe.
  
-=== DC Power Supply Isolation Voltages === +<columns 100% 5% 95%> 
-|<100% 25%> +{{:test-and-measurement:analog-discovery-pro-5250:caution.png?40}} 
-^ +25V and -25V to earth ground, continuous | 60VDC, Measurement Category 1 |||+<newcolumn> 
 +**Caution:** Do not connect the ADP5250 hardware to signals or use for measurements within Measurement Categories III or IV. 
 +</columns> 
 + 
 +==== DC Power Supply Isolation Voltages ==== 
 +|<100% 25%>| 
 +^ +25V and -25V to earth ground, continuous | 60 VDC, Measurement Category 1 ||| 
 + 
 +**Note:** //Measurement Categories CAT I and CAT O (Other) are equivalent. The input circuits are not intended for direct connection to the MAINs building installations of Categories CAT II, CAT III, or CAT IV.//
  
 ---- ----
-====Environmental==== +=====Environmental===== 
-|<100% 25%> +|<100% 25%>|  
-  +^ Operating Temperature | 0 °C to 40 °C || 
-^ Operating temperature | 0 °C to 40 °C || +^ Storage Temperature | -20 °C to 60 °C || 
-^ Storage temperature | -20 °C to 60 °C || +^ Operating Humidity | 10% to 90% RH, non-condensing \\ DMM full accuracy at 10% to 80% || 
-^ Operating humidity | 10% to 90% RH, non-condensing \\ DMM full accuracy at 10% to 80% || +^ Storage Humidity | 5% to 95% RH, non-condensing ||
-^ Storage humidity | 5% to 95% RH, non-condensing ||+
 ^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. || ^ Cooling | Forced air circulation (positive pressurization) through a fan. Fan speed automatically adjusts according to operating conditions. Intake and exhaust locations are on rear of device. Ensure that the intake and exhaust locations are not obstructed. ||
 ^ Pollution Degree | 2 || ^ Pollution Degree | 2 ||
-^ Maximum altitude | 2,000 m ||+^ Maximum Altitude | 2,000 m ||
  
 **Note:** For indoor use only. **Note:** For indoor use only.
Line 398: Line 390:
  
 ==== Shock and Vibration ==== ==== Shock and Vibration ====
-|<100% 25%> +|<100% 25%>| 
- +^ Operational Shock | 30 g peak, half sine, 11 ns pulse (Tested in accordance with IEC 60068-2-27. Test profile developed in accordance with MIL-PRF-28800F.) ||  
-^ Operational shock | 30 g peak, half sine, 11 ns pulse (Tested in accordance with IEC 60068-2-27. Test profile developed in accordance with MIL-PRF-28800F.) ||  +^ Random Vibration (Operating) | 5 Hz to 500 Hz, 0.3 g<sub>rms</sub> || 
-^ Random vibration (Operating) | 5 Hz to 500 Hz, 0.3 grms || +^ Random Vibration (Nonoperating) | 5 Hz to 500 Hz, 2.4 g<sub>rms</sub> (Tested in accordance with IEC 60068-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) ||
-^ Random vibration (Nonoperating) | 5 Hz to 500 Hz, 2.4 grms (Tested in accordance with IEC 60068-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) ||+
  
 ---- ----
- +{{page>test-and-measurement:analog-discovery-pro-5250:certifications&fullpage&noindent}}
-==== Safety ==== +
-This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:  +
-  * IEC 61010-1, EN 61010-1  +
-  * UL 61010-1, CSA 61010-1  +
- +
----- +
- +
-==== Electromagnetic Compatibility ==== +
- +
-This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use; for radio equipment; and for telecommunication terminal equipment:  +
-  * EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity   +
-  * EN 55011 (CISPR 11): Group 1, Class A emissions  +
-  * EN 55022 (CISPR 22): Class A emissions  +
-  * EN 55024 (CISPR 24): Immunity  +
-  * AS/NZS CISPR 11: Group 1, Class A emissions  +
-  * AS/NZS CISPR 22: Class A emissions  +
-  * FCC 47 CFR Part 15B: Class A emissions  +
-  * ICES-001: Class A emissions  +
- +
-**Note:** In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.  +
- +
-**Note:** Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.  +
- +
-**Note:** For EMC declarations and certifications, and additional +
- +
- +
----- +
- +
-====CE Compliance==== +
-This product meets the essential requirements of applicable European Directives, as follows:  +
-  * 2014/35/EU; Low-Voltage Directive (safety)  +
-  * 2014/30/EU; Electromagnetic Compatibility Directive (EMC)  +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
- +
-   +
- +
- +