Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
test-and-measurement:analog-discovery-2:rc-low-pass [2022/09/12 20:07] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.comtest-and-measurement:analog-discovery-2:rc-low-pass [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +====== RC Low-Pass Filter Model vs Real Behavior ======
 +
 +{{ reference:test-and-measurement:analog-discovery-2:rc-low-pass:shot_1.png?600 |}}
 +
 +===== Introduction =====
 +This project performs a frequency sweep from 1kHz to 100kHz on a low-pass RC circuit. The input and output signals are plotted alongside a mathematically modeled signal based on the desired cutoff frequency and capacitor value. The script generates the resistor value needed to achieve the specified cutoff frequency. This project showcases WaveForms' ability to simulate the effects of circuits on a signal, and to aid in comparing those signals to the real circuit performance.
 +----
 +===== Inventory =====
 +  * A Digilent Test and Measurement device that supports WaveForms' //Scope// and //Wavegen// instruments.
 +    * [[https://digilent.com/shop/analog-discovery-2-100ms-s-usb-oscilloscope-logic-analyzer-and-variable-power-supply/|Analog Discovery 2]]
 +    * [[https://digilent.com/shop/analog-discovery-studio-a-portable-circuits-laboratory-for-every-student/|Analog Discovery Studio]]
 +    * //An Analog Discovery (Legacy) can also be used.//
 +  * WaveForms Installation
 +    * [[software:waveforms:waveforms-3:start|Resource Center]]
 +  * {{reference:test-and-measurement:analog-discovery-2:rc-low-pass:rc-low-pass-filter-model-vs-real-behavior.zip|ZIP Archive}}
 +    * //Includes a WaveForms workspace including a script that handles the creation of a stimulus waveform, re-capturing it, capturing the circuit's response to it, and modeling the response.//
 +  * Components for a low-pass RC circuit:
 +    * Breadboard (recommended)
 +    * Capacitor (any value in the nano-Farad range)
 +    * Potentiometer (any value)
 +
 +----
 +===== Description =====
 +Mathematical models of circuits can be used to predict the performance of the real circuit, but the model should be verified in practice by comparing its results with the results of real circuits.
 +
 +In order to perform the comparison, a small external circuit will need to be constructed. The modeled response of the filter is calculated using a Math Channel in WaveForms, which implements the formulas used to calculate the output voltage of an low-pass RC filter for a given frequency. Since the frequency sweep is linear, the frequency is known at every point in time, and thus the filter's momentary response can be calculated. The script also models the phase shift introduced by the RC filter.
 +----
 +===== Setup Instructions =====
 +=== Hardware Setup ===
 +<WRAP group> <WRAP column half>
 +This project requires a small external circuit on which to perform the frequency sweep. The circuit consists of a capacitor and resistor in a low-pass RC filter configuration. Please refer to Figure 1 while creating this circuit and connecting it to your Test and Measurement device.
 +</WRAP> <WRAP column half>
 +{{ reference:test-and-measurement:analog-discovery-2:rc-low-pass:circuit.png?600 |}}
 +
 +<html><center></html>
 +//Figure 1. Test Circuit Schematic//
 +<html></center></html>
 +</WRAP> </WRAP>
 +----
 +=== Software Setup ===
 +<WRAP group> <WRAP column half>
 +Start by downloading and extracting the WaveForms workspace from the {{reference:test-and-measurement:analog-discovery-2:rc-low-pass:rc-low-pass-filter-model-vs-real-behavior.zip|ZIP Archive}} (also linked in the inventory section, above). Open the extracted workspace (filter.dwf3work) in WaveForms.
 +
 +Measure the capacitor's capacitance and replace the default value set on the first line of the script (in the //Script// tab, following the comment block). Be sure to pay attention to the order of magnitude and change the second value in "Math.pow()" accordingly (this is the power to raise 10 by). Decide on the desired cutoff frequency, or leave it as is.
 +</WRAP> <WRAP column half>
 +{{ reference:test-and-measurement:analog-discovery-2:rc-low-pass:shot_2.png?direct&600 |}}
 +
 +<html><center></html>
 +//Figure 2. Script Tab//
 +<html></center></html>
 +</WRAP> </WRAP>
 +----
 +=== Running the Script ===
 +<WRAP group> <WRAP column half>
 +**Run** the script to generate the resistance that the potentiometer is to be set to for the entered capacitor and cutoff frequency. Set the potentiometer to this value and run the script again. 
 +
 +In the //Scope 1// tab, Channel 2 (blue) and Ref 1 (gray) should now have extremely similar outputs. Channel 1 (yellow) is the original waveform, "Vin". Channel 2 (blue) is the real output of the RC filter, "Vout". Finally, Ref 1 (grey) is the modeled RC filter signal.
 +
 +The function generator will perform a sweep from 1kHz to 100kHz, but this range can be changed in the Wavegen window.
 +</WRAP> <WRAP column half>
 +{{ reference:test-and-measurement:analog-discovery-2:rc-low-pass:shot_1.png?direct&600 |}}
 +
 +<html><center></html>
 +//Figure 3. Example Results//
 +<html></center></html>
 +</WRAP> </WRAP>
 +----
 +==== Final Notes ====
 +
 +For more guides and example projects for your Test and Measurement device, please visit its Resource Center, which can be found through this wiki's [[test-and-measurement:start]] page.
 +
 +For technical support, please visit the [[https://forum.digilentinc.com|Digilent Forums]].
 +
 +{{tag>project analog-discovery-2 analog-discovery analog-discovery-studio}}
 +