Differences

This shows you the differences between two versions of the page.

Link to this comparison view

programmable-logic:genesys-zu:getting-started [2021/11/18 16:01] – [First Boot] Damo Ferencprogrammable-logic:genesys-zu:getting-started [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 48: Line 48:
 **Note:** //At time of manufacturing, the programming mode select jumper is set to "SD", and the microSD card with the Out-of-Box Petalinux image is placed in the microSD card slot.// **Note:** //At time of manufacturing, the programming mode select jumper is set to "SD", and the microSD card with the Out-of-Box Petalinux image is placed in the microSD card slot.//
  
-**Note:** //Some boards may contain an empty SD card due to a manufacturing error. If in after the 4.-th instruction teh boot sequence doesn't start you are in this situation. In this case, please check the Getting the Out-of-Box image section at the end of the page. After doing those steps, you can continue here.//+**Note:** //Some boards may contain an empty SD card due to a manufacturing error. If after the 4.-th instruction the boot sequence doesn't start you are in this situation. In this case, please check the Getting the Out-of-Box image section at the end of the page. After doing those steps, you can continue here.//
  
 **Note:** //For more information about the board, please check the [[programmable-logic/genesys-zu/reference-manual|reference manual]].// **Note:** //For more information about the board, please check the [[programmable-logic/genesys-zu/reference-manual|reference manual]].//
Line 115: Line 115:
       * Make sure that the installation includes support for Zynq Ultrascale parts.       * Make sure that the installation includes support for Zynq Ultrascale parts.
     * Petalinux 2020.1:     * Petalinux 2020.1:
-      * //Installation instructions can be found in Chapter 2 of Xilinx's [[https://www.xilinx.com/support/documentation/sw_manuals/xilinx2020_1/ug1144-petalinux-tools-reference-guide.pdf|Petalinux Tools Documentation (UG1144)]]//+      * //Installation instructions can be found in Chapter 2 of Xilinx's [[https://docs.xilinx.com/v/u/2020.1-English/ug1144-petalinux-tools-reference-guide|Petalinux Tools Documentation (UG1144)]]//
   * Github repositories for the Hardware and Software components of the Out-of-Box demo. \\ **Note:** //How to clone these repositories is discussed in further detail below.//   * Github repositories for the Hardware and Software components of the Out-of-Box demo. \\ **Note:** //How to clone these repositories is discussed in further detail below.//
     * [[https://github.com/Digilent/genesys-zu]]     * [[https://github.com/Digilent/genesys-zu]]
Line 227: Line 227:
 Any changes in Vivado to the set of IP connected to the processor over AXI require that the system-user.dtsi file be edited to associate the connected IP with compatible drivers. Any changes in Vivado to the set of IP connected to the processor over AXI require that the system-user.dtsi file be edited to associate the connected IP with compatible drivers.
  
-Additional information on what can be changed and how can be found in Xilinx's [[https://www.xilinx.com/support/documentation/sw_manuals/xilinx2020_1/ug1144-petalinux-tools-reference-guide.pdf|Petalinux Tools Documentation (UG1144)]].+Additional information on what can be changed and how can be found in Xilinx's [[https://docs.xilinx.com/v/u/2020.1-English/ug1144-petalinux-tools-reference-guide|Petalinux Tools Documentation (UG1144)]].
 </WRAP> <WRAP column half> </WRAP> <WRAP column half>
 {{ :reference:programmable-logic:genesys-zu:petalinux-config.png?nolink&600 |}} {{ :reference:programmable-logic:genesys-zu:petalinux-config.png?nolink&600 |}}