Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
programmable-logic:cora-z7:start [2022/09/12 11:07] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.comprogrammable-logic:cora-z7:start [2022/10/04 04:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +     
 +====== Cora Z7 ======
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/cora-z7-zynq-7000-single-core-and-dual-core-options-for-arm-fpga-soc-development/
 +| Manual = [[reference-manual]]
 +| Support = http://forum.digilentinc.com
 +| Title = Cora Z7  
 +| Subtitle = Zynq for Hobbyists and Makers
 +| Header = Features
 +| Bullet = Full support for Vivado and Petalinux design environments
 +| Bullet = 667 MHz Cortex-A9 processor with tightly integrated Xilinx FPGA
 +| Bullet = 512 MB DDR3 memory
 +| Bullet = Arduino shield and Pmod connectors for add-on hardware devices
 +| Bullet = USB and Ethernet connectivity
 +| Bullet = Large array of general purpose input/output ports for any number of different custom solutions
 +| Bullet = Small form factor and mounting holes
 +| Bullet = Programmable from JTAG and microSD card 
 +| Header = Key FPGA Specifications
 +| Part Number = XC7Z007S-1CLG400 \\ (XC7Z010-1CLG400*)
 +| Logic Slices = 3,600 (4,400*)
 +| 6-input LUTs =  14,400 (17,600*)
 +| Flip-Flops = 28,800 (35,200*)
 +| Block RAM = 225 KB (270 KB*)
 +| DSP Slices = 66 (80*)
 +| Clock Resources = Zynq PLL with 4 outputs \\ 2 PLLs \\ 2 MMCMs \\ 125 MHz external clock
 +| Internal ADC = Dual-channel, 1 MSPS
 +| Bullet = (*Z7-10 variant value in parentheses where different)
 +| Header = Connectivity and On-board I/O
 +| USB = USB-UART \\ USB-JTAG Programmer \\ USB Host
 +| Ethernet = Gigabit Ethernet PHY
 +| Pmod Connectors = 2
 +| Other Connectors = Arduino/chipKIT shield connector \\ MicroSD Card Slot
 +| Buttons = 2 Push buttons 
 +| LEDs = 2 RGB LEDs
 +| Header = Electrical
 +| Power Inputs = USB \\ 5V External source
 +| Header = Physical
 +| Width = 2.28 in (57.9 mm)
 +| Length = 4.00 in (101.6 mm)
 +| Header = Design Resources
 +| Mechanical Drawing = {{:reference:programmable-logic:cora-z7:cora_z7_dimensions.zip| DXF }}
 +| Header = Product Compliance
 +| HTC = 8473301180
 +| ECCN = EAR99
 +}}
  
 +{{page>reference-manual}} \\ \\
 +
 + ===== Documentation =====
 +{{topic>cora-z7 +doc -legacy}}
 +
 +----
 +===== Tutorials =====
 +
 +  * [[programmable-logic:guides:installing-vivado-and-vitis]]
 +    * Walks through installing Vivado and Vitis, the development environments used to create hardware and software applications targeting Digilent FPGA development boards.
 +  * [[programmable-logic:guides:getting-started-with-ipi]]
 +    * Walks through using Vivado and Vitis to create a design in hardware and software that uses a processor to control buttons and LEDs.
 +  * [[programmable-logic:guides:getting-started-with-vivado]]
 +    * Walks through using Vivado to create a simple design that blinks a single LED.
 +  * [[learn/programmable-logic/tutorials/pmod-ips/start]]
 +    * Digilent Pmod IPs can be used to control connected Pmods from baremetal software.
 +    * It should be noted that not all Pmods are supported and that Pmod IPs are only supported in versions of Vivado 2019.1 and older.
 +
 +----
 +===== Example Projects =====
 +
 +=== Demos Supporting Vivado and Vitis 2020.1 ===
 +  * [[./demos/pmod-vga]]
 +  * [[./demos/basic-io]]
 +  * [[./demos/xadc]]
 +=== Other Demos ===
 +  * [[pmod/pmodi2s2/fpga-demo]]
 +
 +----
 +===== Additional Resources ===== 
 +
 +{{topic>cora-z7 +additional-resource -legacy}}
 +
 +
 +----
 +
 +{{tag>programmable-logic cora-z7 resource-center}}