Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodstep:start [2022/09/13 14:56] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodstep:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod STEP  ======
 +  
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-step-stepper-motor-driver/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod STEP
 +| Subtitle = Stepper Motor Driver
 +| Header = Features
 +| Bullet = Stepper motor driver for 4 and 6-pin motors
 +| Bullet = Can drive both motors simultaneously
 +| Bullet = Multiple LEDs to indicate signal propagation
 +| Bullet = Jumper for optional external power
 +| Bullet = 2×6-pin Pmod connector with GPIO interface
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 1
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 2.8 in (7.11 cm)
 +| Length = 1.3 in (3.30 cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodstep:pmodstep.fzpz| }}
 +| Header = Documentation
 +| Primary IC = [[http://www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/CD00000059.pdf | L293DD]]
 +| Reference Manual = [[pmod/pmodstep/reference-manual]]
 +| Schematic = {{reference:pmod:pmodstep:pmodstep_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-2x6.png?direct |}}
 +| Pin 1 = SIG1
 +| Pin 2 = SIG2
 +| Pin 3 = SIG3
 +| Pin 4 = SIG4
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Pin 7 = SIG5
 +| Pin 8 = SIG6
 +| Pin 9 = SIG7
 +| Pin 10 = SIG8
 +| Pin 11 = GND
 +| Pin 12 = VCC
 +}}
  
 +{{page>reference-manual}} \\ \\
 + 
 +
 +
 +===== Example Projects =====
 +
 +==Microprocessor==
 +  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
 +  * [[http://www.instructables.com/id/Electrical-Connections-on-the-3D-Printed-IPad-Moun/?ALLSTEPS|Electrical Connections on the 3D Printed IPad Mount]] - Community Project
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-step-with-arduino-uno-beca10|Using the Pmod STEP with Arduino Uno]] - Application note
 +==Programmable Logic==
 +  * [[http://www.instructables.com/id/How-to-Control-a-Stepper-Motor-With-an-FPGA/|How to control a stepper motor with an FPGA]] - Community Project
 +  * [[http://www.instructables.com/id/Using-the-PmodJSTK-to-Control-Stepper-Motors-on-th/|Using a Joystick to control Stepper Motors with an FPGA]] - Community Project
 +
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +  * [[https://www.instructables.com/id/How-to-use-a-Stepper-Motor/|How to use a Stepper Motor]] Instructable
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-gpio pmodstep stepper-motor resource-center}}