Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodssr:start [2022/09/13 17:53] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodssr:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod SSR ======
 +   
 +   
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-ssr-solid-state-relay-electronic-switch/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod SSR
 +| Subtitle = Solid State Relay
 +| Header = Features
 +| Bullet = 0-48 V blocking voltage
 +| Bullet = Can switch up to 6 A<sub>rms</sub> continuous current
 +| Bullet = 2500 V input/output isolation
 +| Bullet = Low on resistance with fast turn on/off
 +| Bullet = Onboard LED to indicate on/off state
 +| Bullet = Onboard terminal block for easy wire connection
 +| Bullet = Follows the Digilent Pmod Interface Specification Type 1
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 1.7 in (4.32 cm)
 +| Length = 0.80 in (2.03 cm)
 +| Overall Height = 0.75 in (1.905 cm)
 +| Header = Design Resources
 +| 3D CAD file = {{reference:pmod:pmodssr:pmod_ssr.zip|STP file}}
 +| Header = Documentation
 +| Reference Manual = [[pmod/pmodssr/reference-manual]]
 +| Schematic = {{reference:pmod:pmodssr:pmodssr_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = ON
 +| Pin 2 = NC
 +| Pin 3 = NC
 +| Pin 4 = NC
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +}}
  
 +{{page>reference-manual}} \\ \\
 + 
 +
 +
 +===== Example Projects =====
 +==Microprocessor==
 +  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
 +  * {{:reference:pmod:pmodssr:pmod_ssr_demo.zip|Example Code for Arduino IDE}}
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-ssr-with-arduino-uno-f1ff96|Using the Pmod SSR with Arduino Uno]] - Application note
 +==Programmable Logic==
 +  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
 +     * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier.
 +  * {{ :reference:pmod:pmodssr:ssr_hdl.zip |Basys 3 Verilog Example - Vivado 2016.4}}
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-gpio pmodssr resource-center}}