Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodsf3:start [2022/09/08 14:05] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodsf3:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +    
 +====== Pmod SF3  ======
 +   
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-sf3-32-mb-serial-nor-flash/
 +| Manual = [[reference:pmod:pmodsf3:reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod SF3
 +| Subtitle = 32MB Serial NOR Flash
 +| Header = Features
 +| Bullet = 32MB serial NOR Flash memory
 +| Bullet = Supports extended SPI protocol, dual I/O, and quad I/O
 +| Bullet = Minimum 100,000 erase cycles per sector
 +| Bullet = More than 20 years data retention
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}}
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/spi/start | SPI]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 1.0 in (2.51 cm)
 +| Length = 0.80 in (2.03cm)
 +| Header = Design Resources
 +| Header = Documentation
 +| Primary IC = [[https://www.micron.com/parts/nor-flash/serial-nor-flash/n25q256a13esf40g?pc=%7B8211C822-468A-4C3B-A530-ECB074FBE385%7D | Data Sheet ]]
 +| Reference Manual = [[pmod/pmodsf3/reference-manual]]
 +| Schematic = {{:reference:pmod:pmodsf3:pmodsf3_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-2x6.png?direct |}}
 +| Pin 1 = ~CS
 +| Pin 2 = MOSI
 +| Pin 3 = MISO
 +| Pin 4 = SCLK
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Pin 7 = NC
 +| Pin 8 = RST#
 +| Pin 9 = WP#
 +| Pin 10 = HLD#
 +| Pin 11 = GND
 +| Pin 12 = VCC
 +}}
  
 +{{page>reference-manual}} \\ \\
 +
 +---- 
 +
 +
 +===== Example Projects =====
 +==Microprocessor==
 +  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
 +  * {{ :reference:pmod:pmodsf3:sf3.zip | Library and MPIDE Example}}
 +
 +==Programmable Logic==
 +  * Arty A7 100T project using the Pmod SF3 and Pmod CLS created by user Tim S. on the Digilent Forum [[https://forum.digilentinc.com/topic/20419-spi-memory-tester-ipi-bd-and-vhdl/|Forum thread]]
 +  * Zybo Z7-20 project using the Pmod SF3 and Pmod CLS created by user Tim S. on the Digilent Forum [[https://forum.digilentinc.com/topic/20460-spi-memory-tester-ipi-bd-for-zynq/|Forum thread]]
 +  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
 +     * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier.
 +
 +
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-spi pmodsf3 resource-center}}