Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodhb5:start [2022/09/13 14:47] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodhb5:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod HB5  ======
 +  
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-hb5-h-bridge-driver-with-feedback-inputs/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod HB5
 +| Subtitle = H-bridge Driver with Feedback Inputs
 +| Header = Features
 +| Bullet = 2A H-bridge circuit
 +| Bullet = Drive a DC motor with operating voltage up to 12V
 +| Bullet = 6-pin JST connector for direct connection to Digilent motor/gearboxes
 +| Bullet = Two screw terminals for external motor power supply
 +| Bullet = 6-pin Pmod port with GPIO interface
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 5
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 1.2 in (3.05 cm)
 +| Length = 0.80 in (2.03 cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodhb5:pmodhb5.fzpz| }}
 +| Header = Documentation
 +| Reference Manual = [[pmod/pmodhb5/reference-manual]]
 +| Schematic = {{reference:pmod:pmodhb5:pmodhb5_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = DIR
 +| Pin 2 = EN
 +| Pin 3 = SA
 +| Pin 4 = SB
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Header = J2 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = SB
 +| Pin 2 = SA
 +| Pin 3 = GND
 +| Pin 4 = VCC
 +| Pin 5 = M+
 +| Pin 6 = M-
 +}}
  
 +{{page>reference-manual}} \\ \\
 + 
 +
 +===== Example Projects =====
 +
 +
 +== Microprocessor==
 +  * {{:reference:pmod:pmodhb5:pmodhb5-mpide-lib.zip|Library and MPIDE Example}}
 +  * {{:reference:pmod:pmodhb5:pmodhb5_mplab_library.zip|Library and MPLAB Example}}
 +  * [[http://www.instructables.com/id/Racing-Robots/|Racing Robots!]] - Community Project
 +  * [[http://www.instructables.com/id/Behind-You-Anti-Creeper-Alert-System/|Behind You! Anti Creeper Alert System]] - Community Project
 +  * [[http://www.instructables.com/id/EMS-Diagnostic-Robot-with-BPM/|EMS Diagnostic Robot with BPM]] - Community Project
 +  * [[http://www.instructables.com/id/Digilent-MRK-Line-Following-Robot-Assembly-Instruc/|Digilent MRK + Line-Following Robot Assembly Instructions]] - Community Project
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-hb5-with-arduino-uno-fb3e43|Using the Pmod HB5 with Arduino Uno]] - Application note
 +
 +==Programmable Logic==
 +  * {{:reference:pmod:pmodhb5:pmodhb5_demo_verilog.zip|Nexys 3 Verilog Example - ISE 14.2}}
 +  * {{:reference:pmod:pmodhb5:pmodhb5_ise_demo.zip|Nexys 3 VHDL Example - ISE 13.4}}
 +  * {{:reference:pmod:pmodhb5:pmodhb5_demo_project.zip|Nexys 3 VHDL Example - ISE 14.2}}
 +  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware/|Setting Up the Zybot - Hardware]] - Community Project
 +  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware-Round-and-Tall-Editi/|Setting up the Zybot - Hardware Round and Tall Edition]] - Community Project
 +
 +==Reference Projects==
 +  * {{:reference:pmod:pmodhb5:pmodhb5_refcomp.zip|Reference Component Example}}
 +  * {{:reference:pmod:pmodhb5:pmodhb5_refproj.zip|Reference Design Example}}
 +
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-gpio pmodhb5 h-bridge-driver resource-center}}