Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodgyro:start [2022/09/13 14:48] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodgyro:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod GYRO ======
  
 +  
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-gyro-3-axis-digital-gyroscope/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod GYRO
 +| Subtitle = 3-axis Digital Gyroscope
 +| Header = Features
 +| Bullet = 3-axis MEMS digital gyroscope with high shock survivability
 +| Bullet = Get angular momentum data with user selectable resolution (250/500/2000dps)
 +| Bullet = Two customizable interrupt pins
 +| Bullet = User configurable signal filtering
 +| Bullet = Power-down and Sleep modes
 +| Bullet = 12-pin Pmod port with SPI interface and additional I²C interface
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/spi/start | SPI]], [[learn/fundamentals/communication-protocols/i2c/start | I²C]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3v
 +| Header = Physical
 +| Width = 1.0 in (2.54 cm)
 +| Length = 0.80 in (2.03cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodgyro:pmodgyro.fzpz| }}
 +| Header = Documentation
 +| Primary IC = {{:reference:pmod:pmodgyro:stmicroelectronics-l3g4200d-datasheet.pdf|ST L3G4200D}}
 +| Reference Manual = [[pmod/pmodgyro/reference-manual]]
 +| Schematic = {{reference:pmod:pmodgyro:pmodgyro_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-2x6.png?direct |}}
 +| Pin 1 = ~CS
 +| Pin 2 = MOSI
 +| Pin 3 = MISO
 +| Pin 4 = SCLK
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Pin 7 = INT1
 +| Pin 8 = INT2
 +| Pin 9 = NC
 +| Pin 10 = NC
 +| Pin 11 = GND
 +| Pin 12 = VCC
 +| Header = J2 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-2x4-top-vertical.png?direct |}}
 +| Pin 1/5 = SCL
 +| Pin 2/6 = SDA
 +| Pin 3/7 = GND
 +| Pin 4/8 = VCC
 +}}
 +
 +{{page>reference-manual}} \\ \\
 + 
 +
 +===== Example Projects =====
 +==Microprocessor==
 +  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
 +  * {{:reference:pmod:pmodgyro:pmodgyro-mpide-lib.zip|Library and MPIDE Example}}
 +  * [[http://www.instructables.com/id/How-to-use-I2C-in-LabVIEW/|How to use I2C in LabVIEW]] - Community Project
 +  * [[http://www.instructables.com/id/Auto-balancing-table-1/?ALLSTEPS|Auto-balancing table]] - Community Project
 +  * [[http://www.instructables.com/id/DIY-Prosthetic-Hand/?ALLSTEPS|DIY Prosthetic Hand]] - Community Project
 +  * [[http://www.instructables.com/id/Plug-and-Play-Pmods-Using-LabVIEW/step4/LabVIEW-Code/|Plug and Play Pmods Using LabVIEW]] - Community Project
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-gyro-with-arduino-uno-da7b29|Using the Pmod GYRO with Arduino Uno]] - Application note
 +==Programmable Logic==
 +  * {{:reference:pmod:pmodgyro:pmodgyro_demo_verilog.zip|Nexys 3 Verilog Example - ISE 14.2}}
 +  * {{:reference:pmod:pmodgyro:pmodgyro_demo.zip|Nexys 3 VHDL Example - ISE 14.2}}
 +  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
 +    * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier.
 +
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-spi pmod-i2c pmodgyro gyroscope resource-center}}