Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodcon3:start [2022/09/13 17:52] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodcon3:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod CON3  ======
 +  
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-con3-r-c-servo-connectors/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod CON3
 +| Subtitle = R/C Servo Connectors
 +| Header = Features
 +| Bullet = Four standard 3-wire servo motor connectors
 +| Bullet = Easily interface with Digilent system boards
 +| Bullet = Flexible power delivery to servos
 +| Bullet = 6-pin Pmod port with GPIO interface
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 1
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 1.0 in (2.54 cm)
 +| Length = 0.80 in (2.03 cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodcon3:pmodcon3.fzpz| }}
 +| Header = Documentation
 +| Reference Manual = [[pmod/pmodcon3/reference-manual]]
 +| Schematic = {{reference:pmod:pmodcon3:pmodcon3_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = P1
 +| Pin 2 = P2
 +| Pin 3 = P3
 +| Pin 4 = P4
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +}}
  
 +{{page>reference-manual}} \\ \\
 + 
 +
 +
 +===== Example Projects =====
 +
 +== Programmable Logic==
 +  * {{:reference:pmod:pmodcon3:pmodcon3_demo.zip|VHDL Example}}
 +  * [[http://www.instructables.com/id/Line-Following-SRK-Robot-with-3d-printed-parts/|Line Following SRK Robot with 3D printed parts]] - Community Project
 +  * [[http://www.instructables.com/id/Using-the-PmodCON3-with-chipKIT-products/|Using the PmodCON3 with chipKIT products]] - Community Project
 +  * [[http://www.instructables.com/id/Controlling-Servos-via-Bluetooth-RN-42-and-LabVIEW/|Controlling Servos via Bluetooth (RN-42) and LabVIEW]] - Community Project
 +
 +
 +==Reference Projects==
 +  * {{:reference:pmod:pmodcon3:pmodcon3_refproj.zip|Reference Design}}
 +  * {{:reference:pmod:pmodcon3:pmodcon3_refcomp.zip|Reference Component Design}}
 +  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware/|Setting Up the Zybot - Hardware]] - Community Project
 +  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware-Round-and-Tall-Editi/|Setting up the Zybot - Hardware Round and Tall Edition]] - Community Project
 +  * [[http://www.instructables.com/id/Controlling-Servos-on-FPGA/|Controlling Servos on FPGA]] - Community Project
 +
 +----
 +
 +===== Additional Resources =====
 +{{topic>pmodcon3 +user-guide}}
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-gpio pmodcon3 servo motors resource-center}}