Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodclp:start [2022/09/13 15:27] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodclp:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +   
 +====== Pmod CLP ======
  
 +  
 +{{Digilent Infobox
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod CLP
 +| Subtitle = Character LCD with Parallel Interface
 +| Header = Features
 +| Bullet = 16×2 character LCD with parallel interface
 +| Bullet = 192 predefined characters including 93 ASCII characters
 +| Bullet = Up to 8 user-definable characters
 +| Bullet = Read and write capability to and from the display
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}}
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 2.3 in (5.84 cm)
 +| Length = 3.3 in (8.38 cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodclp:pmodclp.fzpz| }}
 +| Header = Documentation
 +| LCD Controller = {{ :reference:pmod:pmodclp:ks0066.pdf |Samsung KS0066}}
 +| Reference Manual = [[pmod/pmodclp/reference-manual]]
 +| Schematic = {{reference:pmod:pmodclp:pmodclp_sch.pdf| }}
 +| Header = J1 Top Half Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = DB0
 +| Pin 2 = DB1
 +| Pin 3 = DB2
 +| Pin 4 = DB3
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Header = J1 Bottom Half Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 7 = DB4
 +| Pin 8 = DB5
 +| Pin 9 = DB6
 +| Pin 10 = DB7
 +| Pin 11 = GND
 +| Pin 12 = VCC
 +| Header = J2 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
 +| Pin 1 = RS
 +| Pin 2 = R/W
 +| Pin 3 = E
 +| Pin 4 = NC
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +}}
 +
 +{{page>reference-manual}} \\ \\
 + 
 +
 +===== Example Projects =====
 +
 +==Microprocessor==
 +  * {{:reference:pmod:pmodclp:pmodclp-mpide-lcdp-lib.zip|Library and MPIDE Example}}
 +  * {{:reference:pmod:pmodclp:pmodclp.zip|Sending Information to the Display Example}}
 +  * {{:reference:pmod:pmodclp:pmodclp_mplab_library.zip|Library and MPLAB Example}}
 +  * [[http://www.instructables.com/id/LCD-Control-with-LabVIEW/|LCD Control with LabVIEW]] - Community Project
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-clp-with-arduino-uno-95c040|Using the Pmod CLP with Arduino Uno]] - Application note
 +
 +==Programmable Logic==
 +  * {{:reference:pmod:pmodclp:pmodclp_demo_verilog.zip|Nexys 3 Verilog Example - ISE 14.2}}
 +  * {{:reference:pmod:pmodclp:pmodclp_ise_demo.zip|Nexys 3 VHDL Example - ISE 13.4}}
 +  * {{:reference:pmod:pmodclp:pmodclp_demo.zip|Nexys 3 VHDL Example - ISE 14.2}}
 +
 +==Reference Project==
 +  * {{:reference:pmod:pmodclp:pmodclp_refproj.zip|Reference Design}}
 +
 +----
 +
 +===== Additional Resources =====
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +  * {{reference:pmod:pmodclp:pmodclp_3dmodel.zip|3D Model}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-gpio pmodclp character-lcd resource-center}}