Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
pmod:pmodamp2:reference-manual [2022/09/13 17:26] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodamp2:reference-manual [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +====== PmodAMP2 Reference Manual ======
 +The Digilent PmodAMP2 (Revision A) amplifies low power audio signals to drive a monophonic output. This module offers a digital gain select to allow output at a 6 or 12 dB gain with pop-and-click suppression.
  
 +{{Digilent Image Gallery 
 +| image = {{:reference:pmod:pmodamp2:pmodamp2-0.png?direct |}}
 +| image = {{:reference:pmod:pmodamp2:pmodamp2-1.png?direct |}}
 +| image = {{:reference:pmod:pmodamp2:pmodamp2-2.png?direct |}}
 +| image = {{:reference:pmod:pmodamp2:pmodamp2-3.png?direct |}}
 +}} 
 +
 +== Download This Reference Manual == 
 +  * {{:reference:pmod:pmodamp2:pmodamp2_rm.pdf| PDF}}
 +
 +----
 +
 +===== Features =====
 +  * Filterless, high efficiency audio amplifier
 +  * Monophonic audio output
 +  * Standard 1/8" (0.32 cm) mono speaker jack 
 +  * Micropower shutdown mode 
 +  * Pop–and-click suppression 
 +  * Digital gain select 
 +  * 6-pin Pmod port with GPIO interface
 +
 +----
 +=====Functional Description =====
 +The %%PmodAMP2%% utilizes Analog Devices [[http://www.analog.com/static/imported-files/data_sheets/SSM2377.pdf|SSM2377]] Mono Class-D audio amplifier. This module is designed to accept an analog voltage signal as the incoming audio input, although a pulse-width modulated signal can also be easy accepted after it passes through the reconstruction filter. A Σ-Δ modulator internal to the SSM2377 nicely smooths out the incoming analog signal to get a clean audio output signal.
 +
 +----
 +===== Interfacing with the Pmod=====
 +The %%PmodAMP2%% communicates with the host board via the [[pmod:communication_protocols:gpio|GPIO]] protocol. What this entails for us is that there is not a timing protocol that we need to follow. Rather, as long as your incoming digital data has a sample rate of at least 16 kHz, the amplifier will be able to nicely handle the incoming data. Alternatively, an analog signal can be provided and will also result in a corresponding sound output.
 +
 +A gain selection pin and active-low shutdown pins are also available for use. When the gain pin is driven high there is a 6 dB gain applied to the incoming audio signals and a 12 dB gain applied to audio signals when the pin is driven low. 
 +
 +The shutdown pin can be driven to a logic low level to place the SSM2377 into a very low power state with a shutdown current of only 100 nA placing very little strain on the power source. The Pmod can be brought back into normal operation mode by bringing the shutdown pin back to a logic high level for a maximum speaker output of 2.5W.
 +
 +
 +==== Pinout Description Table ====
 +^  Pin  ^  Signal     ^  Description             ^
 +|  1    |  AIN        |  Audio Input             |
 +|  2    |  GAIN       |  Gain Selection          |
 +|  3    |  NC         |  Not Connected           |
 +|  4    |  ~SHUTDOWN  |  Active Low Shutdown     |
 +|  5    |  GND        |  Power Supply Ground     |
 +|  6    |  VCC        |  Power Supply (3.3V/5V)  |
 +
 +**Table 1** Connector J1- Pin Descriptions as labeled on the Pmod
 +
 +Any external power applied to the %%PmodAMP2%% must be within 2.5V and 5.5V; however, it is recommended that the Pmod is operated at 3.3V.
 +----
 +===== Physical Dimensions =====
 +The pins on the pin header are spaced 100 mil apart. The PCB is 1.25 inches long on the sides parallel to the pins on the pin header and 0.8 inches long on the sides perpendicular to the pin header. 
 +----
 +===== Additional Information =====
 +The schematics of the %%PmodAMP2%% are available {{reference:pmod:pmodamp2:pmodamp2_sch.pdf|here}}. Additional information about the audio amplifier including its EMI emissions and THD+N vs Frequency responses can be found by checking out its datasheet [[http://www.analog.com/static/imported-files/data_sheets/SSM2377.pdf|here]]. 
 +
 +Example code demonstrating how to send audio signals to the %%PmodAMP2%% can be found [[pmod:pmodamp2:start#example_projects|here]]. 
 +
 +If you have any questions or comments about the %%PmodAMP2%%, feel free to post them under the appropriate section ("Add-on Boards") of the [[https://forum.digilentinc.com/|Digilent Forum]].