Differences

This shows you the differences between two versions of the page.

Link to this comparison view

pmod:pmodacl2:start [2022/09/08 13:19] – changed forum.digilentinc.com to forum.digilent.com jeff.greenberg_ni.compmod:pmodacl2:start [2022/10/04 04:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +~~NOTOC~~ 
 +     
 +====== Pmod ACL2 ======
 +   
 +{{Digilent Infobox
 +| Store Page = https://digilent.com/shop/pmod-acl2-3-axis-mems-accelerometer/
 +| Manual = [[reference-manual]]
 +| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
 +| Title = Pmod ACL2
 +| Subtitle = 3-Axis MEMS Accelerometer
 +| Header = Features
 +| Bullet = User Selectable Resolution
 +| Bullet = Less than 2 uA consumption at 100 Hz
 +| Bullet = Activity and inactivity monitoring
 +| Bullet = Free fall detection
 +| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}}
 +| Header = Key Specifications
 +| Range = ±2/4/8g
 +| Resolution = 12-bits
 +| FIFO Depth = 512 Samples
 +| Header = Electrical
 +| Bus = [[learn/fundamentals/communication-protocols/spi/start | SPI]]
 +| Specification Version = 1.2.0
 +| Logic Level = 3.3V
 +| Header = Physical
 +| Width = 0.95 in (2.41 cm)
 +| Length = 0.80 in (2.03cm)
 +| Header = Design Resources
 +| Fritzing Part = {{reference:pmod:pmodacl2:pmodacl2.fzpz| }}
 +| Header = Documentation
 +| Primary IC = [[http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL362.pdf | ADXL362]]
 +| Reference Manual = [[reference/pmod/pmodacl2/reference-manual]]
 +| Schematic = {{reference:pmod:pmodacl2:pmodacl2_sch.pdf| }}
 +| Header = J1 Pinout
 +| Full Row = {{ :reference:pmod:pmod-pinout-2x6.png?direct |}}
 +| Pin 1 = ~CS
 +| Pin 2 = MOSI
 +| Pin 3 = MISO
 +| Pin 4 = SCLK
 +| Pin 5 = GND
 +| Pin 6 = VCC
 +| Pin 7 = INT2
 +| Pin 8 = INT1
 +| Pin 9 = NC
 +| Pin 10 = NC
 +| Pin 11 = GND
 +| Pin 12 = VCC
 +| Header = J2 Pinout
 +| Pin 1 = INT1
 +| Pin 2 = GND
 +| Header = J3 Pinout
 +| Pin 1 = INT2
 +| Pin 2 = GND
 +}}
  
 +{{page>reference-manual}} \\ \\
 +
 +---- 
 +
 +===== Example Projects =====
 +==Microprocessor==
 +  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
 +  * {{:reference:pmod:pmodacl2:pmodacl2-mpide-example.zip| Library and MPIDE Example}}
 +  * [[http://www.instructables.com/id/Float-a-Ping-Pong-Ball-at-Will/?ALLSTEPS |Float a ping pong ball at will!]] - Community Project
 +  * [[http://www.instructables.com/id/Raspberry-Pi-Rainbow-Ruler/ |Raspberry Pi Rainbow Ruler]] - Community Project
 +  * [[https://www.hackster.io/mmigs/using-the-pmod-acl2-with-arduino-uno-ac83fd|Using the Pmod ACL2 with Arduino Uno]] - Application note
 +
 +==Programmable Logic==
 +  * Arty A7 100T project using the Pmod ACL2, Pmod CLS, and Pmod 7SD created by user Tim S. on the Digilent Forum [[https://forum.digilentinc.com/topic/20397-muxssd-driver-for-the-pmod-ssd/|Forum thread]]
 +  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
 +     * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier. 
 +
 +----
 +===== Additional Resources =====
 +  * [[https://wiki.analog.com/resources/fpga/xilinx/pmod/adxl362|ZedBoard Demo Project]]
 +  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
 +
 +----
 +
 +{{tag>pmod pmod-start pmod-spi pmodacl2 accelerometer resource-center}}