Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
learn:programmable-logic:tutorials:nexys-4-getting-started-with-microblaze:start [2016/11/15 01:21] – [13. Selecting Hello World Application from available templates] jon peyronlearn:programmable-logic:tutorials:nexys-4-getting-started-with-microblaze:start [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== Nexys 4 - Getting Started with Microblaze ====== ====== Nexys 4 - Getting Started with Microblaze ======
 +
 +<WRAP round important 660px>
 +=== Important! ===
 +This guide is obsolete, the updated guide can be found [[:vivado:getting-started-with-ipi:start|here]].
 +</WRAP>
 +
 {{ :nexys:nexys4:overview1.png?300 |}} {{ :nexys:nexys4:overview1.png?300 |}}
  
Line 150: Line 156:
 >{{:vivado:mig_18.jpg?500|}} >{{:vivado:mig_18.jpg?500|}}
  
->5.3) This will add a UART block to the existing design. We need a UART controller to communicate between the terminal window on the Host-PC and the Nexys 4 DDR hardware.+>5.3) This will add a UART block to the existing design. We need a UART controller to communicate between the terminal window on the Host-PC and the Nexys 4 hardware.
 > >
 >{{:nexys4-ddr:nexys4ddr-adduart.png?direct&500|}} >{{:nexys4-ddr:nexys4ddr-adduart.png?direct&500|}}
Line 273: Line 279:
  
 ----- -----
-==== 15. Run Configuration Settings for STDIO Connection ====+==== 15. Run Configuration  ====
  
 >15.1) After the FPGA has been successfully programmed with the bit file, from the //Project Explorer// panel, right click on the **display_hello_world** project folder which has been highlighted in the screen capture below.  >15.1) After the FPGA has been successfully programmed with the bit file, from the //Project Explorer// panel, right click on the **display_hello_world** project folder which has been highlighted in the screen capture below. 
 >At the bottom of the drop down list, select **Run As** and then select **launch on hardware**.  >At the bottom of the drop down list, select **Run As** and then select **launch on hardware**. 
  
->{{:learn:programmable-logic:tutorials:nexys-4-getting-started-with-microblaze:image14.jpg?500|}}+>{{:learn:programmable-logic:tutorials:nexys-4-getting-started-with-microblaze:image15.jpg?500|}} 
 +}} 
 +----- 
 +==== 16. Using Terminal Emulator ==== 
 + 
 +You can use any serial terminal you would like including the one on SDK. We use Tera Term. 
 +Refer to this link [[http://en.wikipedia.org/wiki/Tera_Term]] to know what Tera Term is. 
 +You can download and install Tera Term from this link [[http://ttssh2.sourceforge.jp/index.html.en]]  
 + 
 + 
 +>16.1) Establish a serial connection with the correct communication port inside Tera Term.  
 +>Go to //SDK Run Configurations// -> Apply and Run.  
 +>Tera Term will work as a Console by displaying the output.  
 +>Notice that inside the built-in console window of SDK, there is a message displayed that reads // Port COM4 is already in use// indicating that the //COM4// port is in use by Tera Term.  
 +> 
 +>{{:vivado:mig_61.jpg?500|}}
  
 ----- -----
  
 +/*{{tag>learn programmable-logic tutorial nexys-4 microblaze}}*/