Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
learn:instrumentation:tutorials:analog-discovery-studio-spectrum-analyzer [2019/05/31 21:25] – Ian Etheridgelearn:instrumentation:tutorials:analog-discovery-studio-spectrum-analyzer [2022/10/04 11:38] (current) – external edit 127.0.0.1
Line 1: Line 1:
-======Using the Spectrum Analyzer====== +======Using the Spectrum Analyzer (Page has Moved) ======
-This guide walks through the process of setting up WaveForms' //Scope// instrument and capturing some data. The user interface of the instrument is briefly described.+
  
-==== 1. Opening the Scope ==== +<WRAP round important 660px> 
- +This guide has been replaced by [[test-and-measurement:guides:waveforms-spectrum-analyzer]], and is slated to be removed from the Digilent Wiki. Please update all bookmarks and saved links to the new location.
-<WRAP group> +
-<WRAP column half> +
-== 1.1 == +
-Plug in your <test & measurement device>, then start WaveForms and make sure your device is connected. +
- +
-If no device is connected to the host computer when WaveForms launches, the **Device Manager** will launch automatically. +
- +
-Make sure that the device is plugged in and turned on, at which point it will appear in the Device Manager's device list (1.). Click on the device in the list ("DEMO" devices are also listed, which allow the user to use WaveForms and create projects without a physical device) to select it, then click the **Select** button (2.) to close the Device Manager. +
- +
-**Note:** //The Device Manager can be reopened by clicking on the "Connected Device" button in the bottom right corner of the screen (3.), or by selecting "Device Manager" from the "Settings" menu at the top of the screen.//+
 </WRAP> </WRAP>
-<WRAP column half> 
-</WRAP> 
-</WRAP> 
----- 
-<WRAP group> 
-<WRAP column half> 
-== 1.2 == 
-Once the Welcome page loads, in the **Instrument Panel** at the left side of the window, click on the **Spectrum** button to open the //Spectrum// instrument. 
-</WRAP> 
-<WRAP column half> 
-</WRAP> 
-</WRAP> 
----- 
-<WRAP group> 
-<WRAP column half> 
-== 1.3 == 
-Once the //Spectrum// instrument opens, the window contains  
-</WRAP> 
-<WRAP column half> 
-</WRAP> 
-</WRAP> 
- 
----- 
-==== 2. Using the Spectrum Analyzer==== 
- 
-//This section walks through setting up the Spectrum Analyzer tool to analyze the frequency response of a simple signal.// 
-<WRAP group> 
-<WRAP column half> 
-== 2.1 Hardware Setup == 
-In order to measure a signal with the //Spectrum // instrument, there must first be a signal to measure. To this end, step 2.1 of this guide describes setting up a simple loopback circuit that connects the <test & measurement device>'s Waveform Generator and Oscilloscope pins. 
- 
-Connect the <test & measurement device>'s scope channel 1 pin (orange wire) to the device's wavegen channel 1 output pin (yellow wire). For devices that use differential input channels, such as the Analog Discovery Studio with MTE cables, make sure to connect the scope channel 1 negative pin (orange wire with white stripes) to the ground pin associated with wavegen channel 1 (black wire). 
-</WRAP> 
-<WRAP column half> 
-</WRAP> 
-</WRAP> 
----- 
-== 2.2 Input Signal == 
-<WRAP group> 
-<WRAP column half> 
-With the loopback circuit set up, a signal must now be applied to the analog output pins. WaveForms' //Wavegen// instrument will be used to accomplish this. 
- 
-From the //Spectrum// instrument, opened in step 1.2, return to WaveForms' Welcome page by clicking on its tab at the top of the screen. In the Welcome tab, open the //Wavegen// instrument, then click the "Run" button in the control bar near the top of the window to begin outputting a signal. With default settings, a 1V amplitude (2V peak-to-peak) 1kHz sine wave is applied to the wavegen channel 1 output pin. Change the frequency to 500kHz by selecting the Frequency parameter drop down menu or typing into the text field.  
- 
-For more detail on how to use the //Wavegen// instrument, please see the [[learn:instrumentation:tutorials:analog-discovery-studio-waveform-generator:start|Using the Waveform Generator]] guide. 
- 
-Return to the //Spectrum// instrument by clicking on its tab in the bar at the top of the screen. 
-</WRAP> 
-<WRAP column half> 
-</WRAP> 
-</WRAP> 
----- 
- 
- 
- 
- 
  
-{{tag>tutorial analog-discovery-studio}}+{{tag>to-be-removed}}