Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| learn:instrumentation:tutorials:analog-discovery-studio-network-analyzer [2019/05/25 02:00] – Ian Etheridge | learn:instrumentation:tutorials:analog-discovery-studio-network-analyzer [2022/10/04 11:38] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======Using the Network Analyzer====== | + | ======Using the Network Analyzer |
| - | This guide walks through the process of setting up WaveForms' | + | |
| - | ====1. Opening the Network Analyzer==== | + | < |
| - | + | This guide has been replaced by [[test-and-measurement: | |
| - | < | + | |
| - | <WRAP column half> | + | |
| - | ==1.1== | + | |
| - | Plug in your <test & measurement | + | |
| </ | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==1.2== | ||
| - | Once the Welcome page loads, in the instrument panel at the left side of the window, click on the Network button to open the Network Analyzer instrument. | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==1.3== | ||
| - | Once the Network instrument opens, the window contains the plot plane split horizontally into two subplot planes, the control bar above the plot planes, and the configuration panel to the right of the plot plane. | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | |||
| - | ====2. Using the Network Analyzer==== | ||
| - | //This section walks through setting up the Network Analyzer to plot data from the //Wavgen// channels.// | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==2.1 Hardware Setup== | ||
| - | Connect the < | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==2.2 Run the Network Analyzer== | ||
| - | By default, the Network Analyzer uses the < | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==2.3 Plot Plane Axes== | ||
| - | By default, the top plane is the magnitude response of the network port in decibels (from +10dB to -90dB) and the bottom plane is the phase response of the network port in degrees (from +180° to -180°). These respective values are on the left side vertical axis and are adjusted using the configuration panel. | ||
| - | |||
| - | The bottom axis is shared by both plots and by default is frequency from 1kHz to 1MHz. This axis can be adjusted using the control bar. Alternately, | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==2.4 Data Cursors== | ||
| - | To take a quick measurement of the plotted magnitude and phase at a given frequency, click the "Quick Measure: Vertical" | ||
| - | |||
| - | To place one or more single-ended or differential cursors, click the Add Cursor button in the bottom left plane. The first click will generate a single ended cursor and repeated clicks will generate additional differential cursors referenced to the first cursor. To change the differential cursors to single ended, click the arrow icon on that cursor' | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | ====3. Network Analyzer User Interface Overview==== | ||
| - | //This section walks through the wide variety of controls and features present in the //Network// instrument.// | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==3.1 Control Bar== | ||
| - | Above the plot planes where the Single and Run acquisition buttons are located is the control bar. To the right of the acquisition controls is the Scale drop down menu. Click on the arrow to select the bottom axis of the lot plane to be linear or logarithmic. | ||
| - | ---- | ||
| - | To the right of the Scale menu is the Start frequency drop down menu. Click the arrow to display the menu and choose a starting frequency. The desired starting frequency can also be manually typed into the text field. Choose from 1mHz up to 10Mhz. | ||
| - | ---- | ||
| - | To the right of the Start frequency drop down menu is the Stop frequency drop down menu. Click the arrow to display the menu and choose a stopping frequency. The desired stopping frequency can also be manually typed into the text field. Choose from 1mHz up to 10Mhz. | ||
| - | ---- | ||
| - | To the right of the Stop frequency drop down menu is the Samples drop down menu. Click the arrow to display the menu and choose the number of samples per sweep. The desired sample amount can also be manually typed into the text field. Choose from 10 to 10k samples. | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP column half> | ||
| - | ==3.2 Configuration Panel== | ||
| - | </ | ||
| - | <WRAP column half> | ||
| - | FIXME image: device manager? | ||
| - | </ | ||
| - | </ | ||
| - | ---- | ||
| - | |||
| - | {{tag>analog-discovery-studio tutorial}} | + | {{tag>to-be-removed}} |