Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| learn:courses:real-analog-chapter-4:start [2017/01/19 23:04] – [Exercises] Martha | learn:courses:real-analog-chapter-4:start [2022/10/04 11:38] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Real Analog: Chapter 4 ====== | ====== Real Analog: Chapter 4 ====== | ||
| - | | + | [[{}/ |
| - | * {{ : | + | --> |
| - | * {{ : | + | * Lecture Material: |
| - | * {{ : | + | * {{ : |
| - | * {{ : | + | * {{ : |
| - | * {{ : | + | * {{ : |
| - | * {{ : | + | * [[http:// |
| - | * {{ : | + | * [[http:// |
| - | * {{ : | + | * [[http:// |
| - | * {{ : | + | * Chapter 4 Videos: |
| - | + | * [[http:// | |
| + | * [[http:// | ||
| + | * [[http:// | ||
| + | * {{ : | ||
| + | | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| + | * {{ : | ||
| * {{ : | * {{ : | ||
| * {{ : | * {{ : | ||
| + | <-- | ||
| ====== 4. Introduction and Chapter Objectives ====== | ====== 4. Introduction and Chapter Objectives ====== | ||
| Line 48: | Line 61: | ||
| A system is commonly represented as shown in the block diagram of Fig. 4.1. The system has some input, //u(t)//, and some output, //y(t)//. In general, both the input and output can be functions of time; the case of constant values is a special case of a time-varying function. The output will be represented as some arbitrary function of the input: | A system is commonly represented as shown in the block diagram of Fig. 4.1. The system has some input, //u(t)//, and some output, //y(t)//. In general, both the input and output can be functions of time; the case of constant values is a special case of a time-varying function. The output will be represented as some arbitrary function of the input: | ||
| - | $$y \left( t \right) = f \{ u \left( t \right) \} (Eq. 4.1)$$ | + | $$y \left( t \right) = f \{ u \left( t \right) \} \qquad |
| Equation (4.1) is said to be the // | Equation (4.1) is said to be the // | ||
| Line 76: | Line 89: | ||
| ==== Example 4.1: Mass Subjected to an External Force ==== | ==== Example 4.1: Mass Subjected to an External Force ==== | ||
| - | Consider the mass-damper system shown in the figure below. The applied force //F(t)// pushes the mass to the right. The mass's velocity resulting from the applied force is //v(t)//. The mass slides on a surface | + | Consider the mass-damper system shown in the figure below. The applied force //F(t)// pushes the mass to the right. The mass's velocity resulting from the applied force is //v(t)//. The mass slides on a surface |
| {{ : | {{ : | ||
| Line 98: | Line 111: | ||
| {{ : | {{ : | ||
| - | We previously wrote mesh equations for this circuit (for a specific value of $V_{in}$) in [[https:// | + | We previously wrote mesh equations for this circuit (for a specific value of $V_{in}$) in [[/ |
| {{ : | {{ : | ||
| Line 112: | Line 125: | ||
| $$V= 2 \left( i_1 - 3V_x \right)$$ | $$V= 2 \left( i_1 - 3V_x \right)$$ | ||
| - | The above four equations provide an inpuot-output description of the circuit. If desired, they can be combined to eliminate all variables except $V_{in}$ and $V$ and re-written in the form $V = f \{ V_{in} \}$ per equation (1). __Note that all information about the original system, except the relationship between the input and output signals, is lost once we do this__. | + | The above four equations provide an inppot-output description of the circuit. If desired, they can be combined to eliminate all variables except $V_{in}$ and $V$ and re-written in the form $V = f \{ V_{in} \}$ per equation (1). __Note that all information about the original system, except the relationship between the input and output signals, is lost once we do this__. |
| The system-level block diagram for the circuit might then be drawn as: | The system-level block diagram for the circuit might then be drawn as: | ||
| Line 178: | Line 191: | ||
| All of the above relationships are of the form: | All of the above relationships are of the form: | ||
| - | $$y(t) = Kx(t) (Eq. 4.2)$$ | + | $$y(t) = Kx(t) \qquad |
| Where $x(t)$ and $y(t)$ are voltages or currents in the above examples. More generally, $x(t)$ and $y(t)$ can be considered | Where $x(t)$ and $y(t)$ are voltages or currents in the above examples. More generally, $x(t)$ and $y(t)$ can be considered | ||
| Line 286: | Line 299: | ||
| {{ : | {{ : | ||
| - | The circuit above can be consider | + | The circuit above can be considered |
| {{ : | {{ : | ||
| Line 418: | Line 431: | ||
| - All two-terminal networks which contain only sources and resistors will have i-v relationships of the form shown in examples 1, 2, and 3. That is, they will be straight lines of the form $v=m \cdot i + b$. The y-intercept term, b, is due to sources in the network; if there are no sources in the network, $b = 0$ and the //i-v// characteristic will pass through the origin. | - All two-terminal networks which contain only sources and resistors will have i-v relationships of the form shown in examples 1, 2, and 3. That is, they will be straight lines of the form $v=m \cdot i + b$. The y-intercept term, b, is due to sources in the network; if there are no sources in the network, $b = 0$ and the //i-v// characteristic will pass through the origin. | ||
| - Due to the form of the i-v characteristic provided in note 1 above, any two-terminal network can be represented as a single source and a single resistor. | - Due to the form of the i-v characteristic provided in note 1 above, any two-terminal network can be represented as a single source and a single resistor. | ||
| - | - The form of the solution for examples 2 and 3 are the same. Thus, the circuit of example 2 is indistinguishable from a similar circuit with a current source $\frac{V_S}{R_1} in parallel with the resistor $R_1$. Likewise, the circuit of example 3 is indistinguishable from a similar circuit with a voltage source $I_SR_1$ in series with the resistor $R_1$. The equivalent circuits are shown below. | + | - The form of the solution for examples 2 and 3 are the same. Thus, the circuit of example 2 is indistinguishable from a similar circuit with a current source $\frac{V_S}{R_1}$ in parallel with the resistor $R_1$. Likewise, the circuit of example 3 is indistinguishable from a similar circuit with a voltage source $I_SR_1$ in series with the resistor $R_1$. The equivalent circuits are shown below. |
| {{ : | {{ : | ||
| Line 454: | Line 467: | ||
| First, we will kill all sources in circuit A and determine the voltage resulting from an applied current, as shown in Figure 4.8 below. With the sources killed, circuit A will look strictly like an equivalent resistance to any external circuitry. This equivalent resistance is designated as $R_{TH}$ in Figure 4.8. The voltage resulting from an applied current, with circuit A dead is: | First, we will kill all sources in circuit A and determine the voltage resulting from an applied current, as shown in Figure 4.8 below. With the sources killed, circuit A will look strictly like an equivalent resistance to any external circuitry. This equivalent resistance is designated as $R_{TH}$ in Figure 4.8. The voltage resulting from an applied current, with circuit A dead is: | ||
| - | $$v_1 = R_{TH} \cdot i | + | $$v_1 = R_{TH} \cdot i |
| {{ : | {{ : | ||
| Line 464: | Line 477: | ||
| Superimposing the two voltages above results in: | Superimposing the two voltages above results in: | ||
| - | $$v=v_1 + v_{OC} | + | $$v=v_1 + v_{OC} |
| Or | Or | ||
| - | $$v= R_{TH} \cdot i + v_{OC} | + | $$v= R_{TH} \cdot i + v_{OC} |
| Equation (4.5) is Thévenin’s theorem. It indicates that the voltage-current characteristic of any linear circuit (with the exception noted below) can be duplicated by an independent voltage source in series with a resistance $R_{TH}$, known as the //Thévenin resistance// | Equation (4.5) is Thévenin’s theorem. It indicates that the voltage-current characteristic of any linear circuit (with the exception noted below) can be duplicated by an independent voltage source in series with a resistance $R_{TH}$, known as the //Thévenin resistance// | ||
| Line 496: | Line 509: | ||
| {{ : | {{ : | ||
| - | Applying KCL at $v_0$, we obtain: $-2A + \frac{v_0 - 6V}{6\Omega} + \frac{v_0}{3|Omega} = 0 \Rightarrow v_0 = v_{OC} = 6V$. Thus, the Thévenin equivalent circuit is on the left below. Re-introducing the load resistance, as shown on the right below, allows us to easily analyze the overall circuit. | + | Applying KCL at $v_0$, we obtain: $-2A + \frac{v_0 - 6V}{6\Omega} + \frac{v_0}{3\Omega} = 0 \Rightarrow v_0 = v_{OC} = 6V$. Thus, the Thévenin equivalent circuit is on the left below. Re-introducing the load resistance, as shown on the right below, allows us to easily analyze the overall circuit. |
| {{ : | {{ : | ||
| Line 507: | Line 520: | ||
| Once again, we kill all sources in circuit A, as shown in Figure 4.8 above but this time we determine the current resulting from an applied voltage. With the sources killed, circuit A still looks like an equivalent resistance to any external circuitry. This equivalent resistance is designated as $R_{TH}$ in Figure 4.8. The current resulting from an applied voltage, with circuit A dead is: | Once again, we kill all sources in circuit A, as shown in Figure 4.8 above but this time we determine the current resulting from an applied voltage. With the sources killed, circuit A still looks like an equivalent resistance to any external circuitry. This equivalent resistance is designated as $R_{TH}$ in Figure 4.8. The current resulting from an applied voltage, with circuit A dead is: | ||
| - | $$i_1 = \frac{v}{R_{TH}} | + | $$i_1 = \frac{v}{R_{TH}} |
| Notice that equation (4.6) can be obtained by rearranging equation (4.3). | Notice that equation (4.6) can be obtained by rearranging equation (4.3). | ||
| Line 517: | Line 530: | ||
| Employing superposition, | Employing superposition, | ||
| - | $$i = i_1 - i_{SC} | + | $$i = i_1 - i_{SC} |
| So | So | ||
| - | $$i = \frac{v}{R_{TH}} - i_{SC} | + | $$i = \frac{v}{R_{TH}} - i_{SC} |
| Equation (4.8) is Norton’s theorem. It indicates that the voltage-current characteristic of any linear circuit (with the exception noted below) can be duplicated by an independent current source in parallel with a resistance. The current source has the magnitude $i_{SC}$ and the resistance is $R_{TH}$, where $i_{SC}$ is the current seen at the circuit’s terminals if the terminals are short-circuited and $R_{TH}$ is the equivalent resistance of the circuit seen from the two terminals, with all independent sources in the circuit killed. The equivalent Norton circuit is shown in Fig. 4.12. | Equation (4.8) is Norton’s theorem. It indicates that the voltage-current characteristic of any linear circuit (with the exception noted below) can be duplicated by an independent current source in parallel with a resistance. The current source has the magnitude $i_{SC}$ and the resistance is $R_{TH}$, where $i_{SC}$ is the current seen at the circuit’s terminals if the terminals are short-circuited and $R_{TH}$ is the equivalent resistance of the circuit seen from the two terminals, with all independent sources in the circuit killed. The equivalent Norton circuit is shown in Fig. 4.12. | ||
| Line 528: | Line 541: | ||
| === Procedure for Determining Norton Equivalent Circuit: === | === Procedure for Determining Norton Equivalent Circuit: === | ||
| - | - Ordered List ItemIdentify | + | - Identify |
| - Determine the equivalent resistance $R_{TH}$ of the circuit. The approach for determining $R_{TH}$ is the same for Norton circuits as Thévenin circuits. | - Determine the equivalent resistance $R_{TH}$ of the circuit. The approach for determining $R_{TH}$ is the same for Norton circuits as Thévenin circuits. | ||
| - Re-activate the sources and determine the short-circuit current $i_{SC}$ across the circuit terminals. Use any analysis approach you choose to determine the short-circuit current. | - Re-activate the sources and determine the short-circuit current $i_{SC}$ across the circuit terminals. Use any analysis approach you choose to determine the short-circuit current. | ||
| Line 576: | Line 589: | ||
| Equating equations (4.8) and (4.9) leads to the conclusion that: | Equating equations (4.8) and (4.9) leads to the conclusion that: | ||
| - | $$i_{SC} = \frac{v_{OC}{R_{TH}} | + | $$i_{SC} = \frac{v_{OC}}{R_{TH}} |
| Likewise, rearranging equation (4.8) to obtain an expression for v gives: | Likewise, rearranging equation (4.8) to obtain an expression for v gives: | ||
| Line 705: | Line 718: | ||
| Thus, maximum power transfer takes place when the load resistance and the Thevenin resistance of the circuit supplying the power are equal. The above result is sometimes called the //maximum power transfer theorem//. When the conditions of the maximum power transfer theorem are met, the total power delivered to the load is: | Thus, maximum power transfer takes place when the load resistance and the Thevenin resistance of the circuit supplying the power are equal. The above result is sometimes called the //maximum power transfer theorem//. When the conditions of the maximum power transfer theorem are met, the total power delivered to the load is: | ||
| - | $$P_L = \frac{ | + | $$P_L = \frac{(\frac{V_{OC}}{2})^2}{R_{TH}} = \frac{V^2_{OC}}{4R_{TH}} (Eq. 4.17)$$ |
| This is one half of the total power generated by the circuit, half the power is absorbed in the resistance $R_{TH}$. | This is one half of the total power generated by the circuit, half the power is absorbed in the resistance $R_{TH}$. | ||
| Line 715: | Line 728: | ||
| Practical power supplies were discussed in section 2.4. It was seen that the presence of an internal resistance in a voltage or current source limited the power that could be delivered to a circuit connected to the source. Practical power supplies are a special case of the results presented above; we use them below as examples of the application of the above principles. | Practical power supplies were discussed in section 2.4. It was seen that the presence of an internal resistance in a voltage or current source limited the power that could be delivered to a circuit connected to the source. Practical power supplies are a special case of the results presented above; we use them below as examples of the application of the above principles. | ||
| - | In section 2.4, practical voltage sources were modeled as an ideal voltage source $V_S$ in series with some internal resistance $R_S$, as shown in Figure 4.18. This corresponds exactly to a Thevenin circuit with $V_{OC} = V_S and R_{TH} = R_S$. The practical voltage source provides maximum power to a circuit connected to it when the input resistance of the circuit (the equivalent resistance of the circuit, seen at the terminals to which the power source is connected) is equal to the internal resistance of the voltage source. Under these circumstances, | + | In section 2.4, practical voltage sources were modeled as an ideal voltage source $V_S$ in series with some internal resistance $R_S$, as shown in Figure 4.18. This corresponds exactly to a Thevenin circuit with $V_{OC} = V_S$ and $R_{TH} = R_S$. The practical voltage source provides maximum power to a circuit connected to it when the input resistance of the circuit (the equivalent resistance of the circuit, seen at the terminals to which the power source is connected) is equal to the internal resistance of the voltage source. Under these circumstances, |
| $$P = \frac{V^2_S}{4R_S}$$ | $$P = \frac{V^2_S}{4R_S}$$ | ||
| Line 749: | Line 762: | ||
| + | [[{}/ | ||
| + | [[{}/ | ||