~~NOTOC~~ 
   
====== Pmod TC1 ======

  
{{Digilent Infobox
| Store Page = https://digilent.com/shop/pmod-tc1-k-type-thermocouple-module-with-wire/
| Manual = [[reference-manual]]
| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
| Title = Pmod TC1
| Subtitle = K-Type Thermocouple Module with Wire
| Header = Features
| Bullet = K-type thermocouple-to-digital converter
| Bullet = Wide temperature range of -73°C to 482°C with provided wire
| Bullet = ±2°C accuracy from -200°C to 700°C
| Bullet = 14-bit with 0.25°C resolution
| Bullet = Cold-junction temperature compensation
| Bullet = 6-pin Pmod port with SPI interface
| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 2
| Header = Electrical
| Bus = [[learn/fundamentals/communication-protocols/spi/start | SPI]]
| Specification Version = 1.2.0
| Logic Level = 3.3V
| Header = Physical
| Width = 1.0 in (2.54 cm)
| Length = 0.80 in (2.03 cm)
| Header = Documentation
| Primary IC = [[http://datasheets.maximintegrated.com/en/ds/MAX31855.pdf | MAX31855]]
| Thermocouple wire = {{pmod/pmod/tc1/pmodtc1_thermocouplewire.pdf | GG-K-24}}
| Reference Manual = [[pmod/pmodtc1/reference-manual]]
| Schematic = {{reference:pmod:pmodtc1:pmodtc1_sch.pdf| }}
| 3D Model = {{reference:pmod:pmodtc1:pmodtc1.zip| 3D Model}}
| Header = J1 Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 1 = CS
| Pin 2 = NC
| Pin 3 = MISO
| Pin 4 = SCLK
| Pin 5 = GND
| Pin 6 = VCC
}}

{{page>reference-manual}} \\ \\
 

===== Example Projects =====
==Microprocessor==
  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
  * {{:reference:pmod:pmodtc1:pmodtc1_mpide.zip|Library and MPIDE Example}}
  * [[http://www.instructables.com/id/Mpemba-Effect/|Mpemba Effect]] - Community Project
  * [[http://www.instructables.com/id/Reflow-Toaster-Oven/|Reflow Toaster Oven]] - Community Project
  * [[http://www.instructables.com/id/Plug-and-Play-Pmods-Using-LabVIEW/step4/LabVIEW-Code/|Plug and Play Pmods Using LabVIEW]] - Community Project
  * [[https://www.hackster.io/mmigs/using-the-pmod-tc1-with-arduino-uno-1b5ed1|Using the Pmod TC1 with Arduino Uno]] - Application note
==Programmable Logic==
  * [[learn/programmable-logic/tutorials/pmod-ips/start | Getting Started with Digilent Pmod IPs]]
     * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier.

----

===== Additional Resources =====
  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}

----

{{tag>pmod pmod-start pmod-spi pmodtc1 thermocouple resource-center}}