~~NOTOC~~ 
   
====== Pmod LS1  ======
  
{{Digilent Infobox
| Store Page = https://digilent.com/shop/pmod-ls1-infrared-light-detector/
| Manual = [[reference-manual]]
| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
| Title = Pmod LS1
| Subtitle = Infrared Light Detector
| Header = Features
| Bullet = Infrared light detector with on-board sensitivity adjustment
| Bullet = Interface with up to four reflective or transmissive photo detectors
| Bullet = Works with Digilent IR Proximity Sensor
| Bullet = 6-pin Pmod connector with GPIO interface
| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 1
| Header = Electrical
| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
| Specification Version = 1.2.0
| Logic Level = 3.3V
| Header = Physical
| Width = 1.4 in (3.56 cm)
| Length = 0.80 in (2.03 cm)
| Header = Design Resources
| Fritzing Part = {{reference:pmod:pmodls1:pmodls1.fzpz| }}
| Header = Documentation
| Primary IC = [[http://www.mouser.com/ds/2/405/lmv324-n-441150.pdf | LMV324MT]], [[http://www.onsemi.com/pub_link/Collateral/NL27WZ14-D.PDF | NL27WZ14]]
| Reference Manual = [[pmod/pmodls1/reference-manual]]
| Schematic = {{reference:pmod:pmodls1:pmodls1_sch.pdf| }}
| Header = J1 Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 1 = S1
| Pin 2 = S2
| Pin 3 = S3
| Pin 4 = S4
| Pin 5 = GND
| Pin 6 = VCC
}}

{{page>reference-manual}} \\ \\
 


===== Example Projects =====
  * Digilent Pmod IPs are only supported in Vivado and Xilinx SDK versions 2019.1 and earlier.

==Microprocessor==
  * [[learn/software/tutorials/digilent-core-install/start | Installing the Digilent Core for Arduino]]
  * {{:reference:pmod:pmodls1:pmodls1_library_and_example_code.zip|Library and Example Code}}
  * [[http://www.instructables.com/id/Line-Following-MRK-Robot-with-3d-printed-parts/|Line Following MRK Robot with 3d printed parts]] - Community Project
  * [[http://www.instructables.com/id/Line-Following-SRK-Robot-with-3d-printed-parts/|Line Following SRK Robot with 3d printed parts]] - Community Project
  * [[http://www.instructables.com/id/Digilent-MRK-Line-Following-Robot-Assembly-Instruc/|Digilent MRK + Line-Following Robot Assembly Instructions]] - Community Project
  * [[https://www.hackster.io/mmigs/using-the-pmod-ls1-with-arduino-uno-df08e1|Using the Pmod LS1 with Arduino Uno]] - Application note

==Programmable Logic==
  * No programmable logic example projects are available for the Pmod LS1

==Reference Projects==
  * {{:reference:pmod:pmodls1:pmodls1_refproj.zip|Reference Design}}

----

===== Additional Resources =====
  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}

----

{{tag>pmod pmod-start pmod-gpio pmodls1 infrared light-detector resource-center}}