~~NOTOC~~ 
   
====== Pmod CON3  ======
  
{{Digilent Infobox
| Store Page = https://digilent.com/shop/pmod-con3-r-c-servo-connectors/
| Manual = [[reference-manual]]
| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
| Title = Pmod CON3
| Subtitle = R/C Servo Connectors
| Header = Features
| Bullet = Four standard 3-wire servo motor connectors
| Bullet = Easily interface with Digilent system boards
| Bullet = Flexible power delivery to servos
| Bullet = 6-pin Pmod port with GPIO interface
| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}} Type 1
| Header = Electrical
| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
| Specification Version = 1.2.0
| Logic Level = 3.3V
| Header = Physical
| Width = 1.0 in (2.54 cm)
| Length = 0.80 in (2.03 cm)
| Header = Design Resources
| Fritzing Part = {{reference:pmod:pmodcon3:pmodcon3.fzpz| }}
| Header = Documentation
| Reference Manual = [[pmod/pmodcon3/reference-manual]]
| Schematic = {{reference:pmod:pmodcon3:pmodcon3_sch.pdf| }}
| Header = J1 Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 1 = P1
| Pin 2 = P2
| Pin 3 = P3
| Pin 4 = P4
| Pin 5 = GND
| Pin 6 = VCC
}}

{{page>reference-manual}} \\ \\
 


===== Example Projects =====

== Programmable Logic==
  * {{:reference:pmod:pmodcon3:pmodcon3_demo.zip|VHDL Example}}
  * [[http://www.instructables.com/id/Line-Following-SRK-Robot-with-3d-printed-parts/|Line Following SRK Robot with 3D printed parts]] - Community Project
  * [[http://www.instructables.com/id/Using-the-PmodCON3-with-chipKIT-products/|Using the PmodCON3 with chipKIT products]] - Community Project
  * [[http://www.instructables.com/id/Controlling-Servos-via-Bluetooth-RN-42-and-LabVIEW/|Controlling Servos via Bluetooth (RN-42) and LabVIEW]] - Community Project


==Reference Projects==
  * {{:reference:pmod:pmodcon3:pmodcon3_refproj.zip|Reference Design}}
  * {{:reference:pmod:pmodcon3:pmodcon3_refcomp.zip|Reference Component Design}}
  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware/|Setting Up the Zybot - Hardware]] - Community Project
  * [[http://www.instructables.com/id/Setting-Up-the-Zybot-Hardware-Round-and-Tall-Editi/|Setting up the Zybot - Hardware Round and Tall Edition]] - Community Project
  * [[http://www.instructables.com/id/Controlling-Servos-on-FPGA/|Controlling Servos on FPGA]] - Community Project

----

===== Additional Resources =====
{{topic>pmodcon3 +user-guide}}
  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}

----

{{tag>pmod pmod-start pmod-gpio pmodcon3 servo motors resource-center}}