~~NOTOC~~ 
   
====== Pmod CLP ======

  
{{Digilent Infobox
| Manual = [[reference-manual]]
| Support = https://forum.digilentinc.com/forum/7-add-on-boards/
| Title = Pmod CLP
| Subtitle = Character LCD with Parallel Interface
| Header = Features
| Bullet = 16×2 character LCD with parallel interface
| Bullet = 192 predefined characters including 93 ASCII characters
| Bullet = Up to 8 user-definable characters
| Bullet = Read and write capability to and from the display
| Bullet = Follows the Digilent {{/reference/pmod/digilent-pmod-interface-specification.pdf |Pmod Interface Specification}}
| Header = Electrical
| Bus = [[learn/fundamentals/communication-protocols/gpio/start | GPIO]]
| Specification Version = 1.2.0
| Logic Level = 3.3V
| Header = Physical
| Width = 2.3 in (5.84 cm)
| Length = 3.3 in (8.38 cm)
| Header = Design Resources
| Fritzing Part = {{reference:pmod:pmodclp:pmodclp.fzpz| }}
| Header = Documentation
| LCD Controller = {{ :reference:pmod:pmodclp:ks0066.pdf |Samsung KS0066}}
| Reference Manual = [[pmod/pmodclp/reference-manual]]
| Schematic = {{reference:pmod:pmodclp:pmodclp_sch.pdf| }}
| Header = J1 Top Half Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 1 = DB0
| Pin 2 = DB1
| Pin 3 = DB2
| Pin 4 = DB3
| Pin 5 = GND
| Pin 6 = VCC
| Header = J1 Bottom Half Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 7 = DB4
| Pin 8 = DB5
| Pin 9 = DB6
| Pin 10 = DB7
| Pin 11 = GND
| Pin 12 = VCC
| Header = J2 Pinout
| Full Row = {{ :reference:pmod:pmod-pinout-1x6.png?direct |}}
| Pin 1 = RS
| Pin 2 = R/W
| Pin 3 = E
| Pin 4 = NC
| Pin 5 = GND
| Pin 6 = VCC
}}

{{page>reference-manual}} \\ \\
 

===== Example Projects =====

==Microprocessor==
  * {{:reference:pmod:pmodclp:pmodclp-mpide-lcdp-lib.zip|Library and MPIDE Example}}
  * {{:reference:pmod:pmodclp:pmodclp.zip|Sending Information to the Display Example}}
  * {{:reference:pmod:pmodclp:pmodclp_mplab_library.zip|Library and MPLAB Example}}
  * [[http://www.instructables.com/id/LCD-Control-with-LabVIEW/|LCD Control with LabVIEW]] - Community Project
  * [[https://www.hackster.io/mmigs/using-the-pmod-clp-with-arduino-uno-95c040|Using the Pmod CLP with Arduino Uno]] - Application note

==Programmable Logic==
  * {{:reference:pmod:pmodclp:pmodclp_demo_verilog.zip|Nexys 3 Verilog Example - ISE 14.2}}
  * {{:reference:pmod:pmodclp:pmodclp_ise_demo.zip|Nexys 3 VHDL Example - ISE 13.4}}
  * {{:reference:pmod:pmodclp:pmodclp_demo.zip|Nexys 3 VHDL Example - ISE 14.2}}

==Reference Project==
  * {{:reference:pmod:pmodclp:pmodclp_refproj.zip|Reference Design}}

----

===== Additional Resources =====
  * Specification Version 1.2.0: {{reference/pmod/pmod-interface-specification-1_2_0.pdf |PDF}}
  * {{reference:pmod:pmodclp:pmodclp_3dmodel.zip|3D Model}}

----

{{tag>pmod pmod-start pmod-gpio pmodclp character-lcd resource-center}}